Thick Film Chip Resistors
(Lead
-
Free for RM06 Series)
1. Scope :
Document No.
TRM-060S004F
Issued date
page
2007/07/17
1/12
This specification applies for the RM06 Series of thick film chip resistors made by TA-I.
2. Construction:
Over Coat (Color : Black)
Conductor :
(Lead-free or with lead )
Sn Plating
Resistive Element
Ceramic Substrate
Ni Plating
3. Type Designation:
RM
Product Code
RM : Chip Resistor
06
Size
Power Rating
J
Tolerance
TN
Packaging
103
Nominal
Resistance
06-0603(1608) 1/10W
J -
±5%
G -
±2%
F -
±1%
D -
±0.5%
B -
±0.1%
T - Paper Tape
+N: Lead-Free
Special :
L : 06 –2mm pitch
paper Tape
3 digits, e.g.,:
(E-24) 103 = 10kΩ
0 = 0
Ω
4 digits, e.g.,:
(E-96) 1540 = 154Ω
43R2 = 43.2Ω
TA-I TECHNOLOGY CO., LTD
Thick Film Chip Resistors
(Lead
-
Free for RM06 Series)
4. Dimensions:
Document No.
TRM-060S004F
Issued date
page
2007/07/17
2/12
UNIT: mm
Type
RM06
L
1.60±0.10
W
0.80±0.10
C
0.30±0.20
0.30
d
+0.2
-0.1
t
0.45±0.10
5. Ratings & Characteristics :
Type
Power
Rating
at 70℃
Rated
Voltage
Max.
Working
Voltage
Max.
Over-
Load
Voltage
Resistance Range(Ω)
T.C.R
(PPM/℃)
B(±0.1%)
E-96
10Ω-560kΩ
D(±0.5%)
E-96
10Ω-1MΩ
F(±1%)
E-96
10Ω-1MΩ
1M＜R≦10MΩ
10Ω-10MΩ
G(±2%)
E-24
J(±5%)
E-24
±100
RM06 1/10W
Refer 5.2
50V
100V
±200
±400
10Ω-10MΩ
1-9.1Ω
10M＜R≦22MΩ
1Ω-9.1Ω
1Ω-9.1Ω
OΩ THICK FILM CHIP RESISTORS
Type
RM06
Rated Current
1A
Max Overload Current
2.5A
Resistance Range
50mΩ MAX
2. Operating Temp(℃): : -55℃
〜
+125℃
Note : Except for the above standardized products , we also provide the customized products.
TA-I TECHNOLOGY CO., LTD
Thick Film Chip Resistors
(Lead
-
Free for RM06 Series)
5.1 Derating Curve :
Document No.
TRM-060S004F
Issued date
page
2007/07/17
3/12
For resistors operated at ambient temperature over 70℃ , power rating shall be derated in
accordance with figure 1.
P max.
100
Power ratio ( % )
50
0
-55
50
Figure 1
70
100
125
Ambient
Temp. (
°C
)
5.2 Rated Voltage:
The rated voltage is calculated by the following formula:
E=
P*R
E=
Rated Voltage(V)
P=
Rated Power(W)
R=
Resistance Value
(Ω)
E.G. : What is RM06JTN102 the rated voltage ?
RM06JTN102 P:1/10W ; R:102 = 1KΩ = 1000Ω
E=
0.1(W) * 1000(Ω)
= 10 (V)
TA-I TECHNOLOGY CO., LTD
Thick Film Chip Resistors
(Lead
-
Free for RM06 Series)
6. Reliability Tests: (As specified in JIS C 5202)
Test Items
Temperature
Resistance
Coefficient
of
Document No.
TRM-060S004F
Issued date
page
2007/07/17
4/12
Reference
standard
JIS-C5202-5.2
Condition of Test
-55〜 +125
℃
Test Limits
Refer 5.0
±
(1% + 0.05Ω )
Short Time Overload
JIS-C5202-5.5
2.5 X rated voltage
for
5 sec
0Ω
: 50mΩ or less
Intermittent Overload
JIS-C5202-5.8
3.0 X rated voltage or Max Overloading
voltage ,1sec “ON” , 25sec “OFF” , 10000 cycle
±
(5.0% + 0.1Ω)
0Ω :
50mΩ or less
Load Life
JIS-C5202-7.10
1000 hours at rated voltage, 70℃ , 1.5hours
“ON “, 0.5hour “OFF”
0.5%,1%:±(1.0%+0.05Ω)
2%,5%:±(3.0%+0.1Ω)
0Ω
:
100mΩ or less
Load Life with Humidity
JIS-C5202-7.9
1000 hours at rated voltage , 40±2℃,
90~95% RH 1.5hours “ON “, 0.5hour “OFF”
0.5%,1%:±(1.0%+0.05Ω)
2%, 5%:±(3.0%+0.1Ω)
0Ω : 100mΩ or less
Without mechanical damage
0.5%,1% :
±(0.5%+0.05Ω)
2%, 5% :±(1.0%+0.05Ω)
0Ω :
50mΩ or less
Rapid Change of Temperature
JIS-C5202-7.4
-55℃ (30 min. ) / +155
℃(30
min. ) 5 cycles
Solderability
JIS-C5202-6.11
245±5℃ solder, 2±0.5 sec dwell.
Solder : Sn96.5 / Ag3.0 / Cu0.5
At least 95% of surface area
of electrode shall be covered
with new solder.
0.5%,1%:±(0.5%+0.05Ω)
2%,5%:±(1.0%+0.05Ω)
0Ω:
50mΩ or less
Robustness
(Bending)
of
Termination
JIS-C5202—6.1
3mm deflection
Dielectric
Withstanding
JIS-C5202-5.7
Voltage (Voltage Proof)
Applying voltage :
300V for a minute .
No abnormalities such as
flashover,
burning
dielectric
breakdown shall appear.
Insulation Resistance
JIS-C5202-5.6
Applying voltage 100V for 1 minute.
≧1GΩ
Resistance to Dry Heat
JIS-C5202-7.2
125±5℃ for 96±4Hrs
0.5%,1% :±(1.0%+0.05Ω)
2%,5% :
±(2.0%+0.1Ω)
0Ω:
50mΩ or less
Resistance to Solder Heat
JIS-C5202-6.10
270
±5℃
solder , 10
±1
sec dwell .
0.5%,1%:±(0.5%+0.05Ω)
2%, 5%:±(1.0%+0.05Ω)
0Ω:
50mΩ or less
TA-I TECHNOLOGY CO., LTD
Thick Film Chip Resistors
(Lead
-
Free for RM06 Series)
Document No.
TRM-060S004F
Issued date
page
2007/07/17
5/12
Component , Lead-Free Soldering part 8 :
Solder Heat Resistance Test for SMD. Lead-
Free Soldering “
Temp. Cycles :
-35
±
5℃ / 125
±
5℃ , Keep 7 min
Testing duration : 500±4 hours
Temp. Humidity Chambers:
Temperature : 85℃
Humidity : 85% RH
Testing duration : 500±4 hours
Whisker
SONY
SS-00254-8
Whisker formation :
50 um or less .
.
Component , Lead-Free Soldering part 5 :
Solder Heat Resistance Test for SMD. Lead-
Free Soldering “
Flow Solder :
Pre – heat : 100 to 105
℃
30±5 sec
Temperature : 260±3℃ 10 +1/ -0 sec
The entire sample shall be dipped in solder.
The specimen shall be stored at standard
atmospheric conditions for 1 hour .
Iron Solder :
Bit temperature : 350
±10℃
Application time of soldering iron : 3 +1/- 0sec
Apply the soldering iron to the electrode .
The specimen shall be stored at standard
atmospheric conditions for 1 hour , after
which the measurements shall be made
Resistance to Solder Heat
SONY
SS-00254-5
Electrical characteristics shall be
Satisfied .
Without distinct deformation in
appearance
Note* : RCWV : Rated continuous working voltage
.
7. Marking :
7.1
±2%
&
±5%(E24)
Resistance value is expressed by 3 digits, the first two digits represent the significant figures of
nominal resistance value inΩ, and the third digit represents exponent for base of 10.
E.G. :, 472 = 47×10
2
= 4700Ω = 4.7KΩ
7.2
±1%
(E96 )
Resistance value is expressed by 4 digits or 3digits , the first three digits represent the significant
figures of nominal resistance value inΩ, and the fourth digit represents exponent for base of 10.
E.G. : 4701 = 470×10
1
= 4700Ω = 4.7K
TA-I TECHNOLOGY CO., LTD
京公网安备 11010802033920号
EEWORLD
