Ruthenium oxide dielectric offers superior resistance to the elements.
3) Electrodes not corroded by soldering
Thick film makes the electrodes very strong.
4) Leading the world in development and mass production.
Since start of production in 1982 (first in the wold), this component has established a solid reputation as a general–
purpose chip resistor.
5) ROHM resistors have approved ISO–9001 certification.
Design and specifications are subject to change without notice. Carefully check the specification sheet before using or
ordering it.
!Ratings
Item
Rated power
Conditions
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
100
80
POWER LOAD (%)
Specifications
0.125W (1 / 8W)
at 70°C
60
40
20
0
−55
0
70
100
155
AMBIENT TEMPERATURE (
°
C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation.
If the value obtained exceeds the limiting element voltage,
the voltage rating is equal to the maximum operating voltage.
E: Rated voltage (V)
E= P×R
P: Rated power (W)
R: Nominal resistance (Ω)
Nominal resistance
Operating temperature
See Table 1.
−55°
C
∼
+ 155°C
Limiting element voltage
150V
1/5
MCR10
Resistors
Jumper type
Resistance
Rated current
Max. 50mΩ
2A
Table 1
Resistance tolerance
F (±1%)
Resistance range
(Ω)
Resistance temperature coefficient
(ppm/°C)
Operating temperature
−55°C
to
+155°C
0.1
≤
R
<
0.15 (E24)
0.15
≤
R
<
10 (E24)
10
≤
R
≤
2.2M (E24,96)
0.1
≤
R
<
0.15 (E24)
0.15
≤
R
<
1
1.0
≤
R
<
2.2
2.2
≤
R
<
10
(E24)
(E24)
(E24)
400±200
±250
±100
400±200
±250
500±350
±500
±200
J (±5%)
10
≤
R
≤
10M (E24)
!Before
using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
!
Characteristics
Item
Resistance
Variation of resistance
with temperature
Overload
±
(2.0%+0.1Ω)
Guaranteed value
Resistor type
Jumper type
J :
±5%
F :
±1%
Max. 50mΩ
Test conditions (JIS C 5201-1)
JIS C 5201-1 4.5
JIS C 5201-1 4.8
Measurement :
−55
/
+25
/
+125°C
JIS C 5201-1 4.13
Rated voltage (current)
×2.5,
2s.
Maximum overload voltage : 200V
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235±5°C
Duration of immersion : 2.0±0.5s.
JIS C 5201-1 4.18
Soldering condition : 260±5°C
Duration of immersion : 10±1s.
JIS C 5201-1 4.19
Test temp. :
−55°C~+125°C
5cyc
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h~1,048h
JIS C 5201-1 4.25.1
Rated voltage (current), 70°C
1.5h : ON
−
0.5h : OFF
Test time : 1,000h~1,048h
JIS C 5201-1 4.25.3
155°C
Test time : 1,000h~1,048h
JIS C 5201-1 4.29
23±5°C, Immersion cleaning, 5±0.5min.
Solvent : 2-propanol
JIS C 5201-1 4.33
See Table.1
Max. 50mΩ
Solderability
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
±
(1.0%+0.05Ω)
Max. 50mΩ
No remarkable abnormality on the appearance.
±
(1.0%+0.05Ω)
±
(3.0%+0.1Ω)
Max. 50mΩ
Max. 100mΩ
Resistance to
soldering heat
Rapid change of
temperature
Damp heat, steady state
±
(3.0%+0.1Ω)
Endurance at 70°C
±
(3.0%+0.1Ω)
Endurance
±
(1.0%+0.05Ω)
Resistance to solvent
Max. 100mΩ
Max. 100mΩ
Max. 50mΩ
Bend strength of
the end face plating
Max. 50mΩ
±
(1.0%+0.05Ω)
Without mechanical damage such as breaks.
2/5
MCR10
Resistors
!External
dimensions
(Units : mm)
1
0.4±0.2
2
3
No.
1
Material
Resistive element
(Oxide metal thick film)
Silver palladium thick film electrode
Nickel electrode
Sn/Pb or Sn electrode
Alumina substrate
Overcoating (glass)
0.4±0.2
2.0±0.1
5
0.55±0.1
4
2
3
4
5
6
!
Packaging
Reel
Taping
P
0
P
2
P
1
φD
0
E
F
B
0
08
06
04
02
02
04
06
08
1.25±0.1
6
W
A
B
D
A
0
Heat crimp cover/Tape
Thick paper (Underside paper tape) Chip resistor Square punchout hole
[i=s]This post was last edited by Maoqiu Dada on 2022-4-27 18:00[/i]Abstract: Based on the car and the Raspberry Pi development board, the system is equipped with cameras, sensors and other data acqui...
[align=center][/align] [align=left]TI has recently launched two new isolation products: ISO224 isolation amplifier and ISO1042 CAN transceiver. :titter:, I still prefer products with isolation functio...
[align=left][color=rgb(25, 25, 25)][font="]Most of the time, the circuit diagrams and designs that appear in textbooks are very different from the real circuits we complete every day in our work. Circ...
[align=center][font=微软雅黑][size=4][color=black]STM32WB55[/color] Review 1: ST's Attack[/size][/font][/align][align=left][font=微软雅黑][size=4] First of all, I would like to thank ST and EE for organizing ...
In the TTL inverter circuit, the book mentions that when the input is high level, VT4 is saturated due to the large base current. However, I think that at this time, because VT3 is cut off, there is n...
Due to various interferences, MSP430 will always fluctuate when performing ADC conversion. In order to improve the reliability of data, software filtering can be performed, among which the mean filter...
Amid increasingly fierce competition in the distributed photovoltaic market, Tianqing Yuanchu recently announced that its latest product, the Integ O series three-phase 4-25kW grid-connected invert...[Details]
Take the program as an example: #include reg52.h sbit led=P3^0; void main() { IT0=1; //Set the trigger mode of external interrupt 0 to falling edge EX0=1; // Enable external int...[Details]
Until now, designers have faced a trade-off in ADC selection. Pipeline converters offer high resolution and wide dynamic range, but their power consumption is quite high. The alternative, discrete-...[Details]
Viavi Solutions announced that it will provide industry-leading 5G wireless and optical network testing solutions to China Mobile. As a trusted supplier of China Mobile, VIAVI has maintained close co...[Details]
Preface Looking at the CDK project (wm_sdk_w800_20210513toolsw800projectsSDK_ProjectprojectCDK_WSCDK_WS.cdkws), I want to add the parameter reading and writing I need based on the official website. ...[Details]
A report released by market research firm Gartner on Thursday showed that global semiconductor market sales in 2021 increased 26.3% year-on-year to US$595 billion, with Samsung Electronics surpassing...[Details]
Background introduction: The turnout indication system is a device that detects the direction of the switch machine and the operating current. It is an important part of the centralized signal monito...[Details]
Foxconn has been seeking to develop in the electric vehicle sector recently, and previously planned to build its first electric vehicle factory in the United States. It is reported that Foxconn's par...[Details]
With the holding of MWC, the attention to 5G has increased again, and the process of 5G integration into thousands of industries is accelerating. MWC provides a view of 5G empowerment of the industry...[Details]
Equipped with an integrated inductor, these power modules will enable customers to achieve a more streamlined design while saving system space.
Currently, servers, communications, a...[Details]
On November 11, sources Jukanlosreve and yeux1122 revealed that both Apple and Samsung's ultra-thin high-density battery projects have failed in development. The two companies had previously attemp...[Details]
When SM2..0 is 011, the SLEEP instruction will put the MCU into power saving mode. This mode is different from the power down mode in one respect: If the Timer/Counter 0 is asynchronously driven, tha...[Details]
Traditional disaster relief vehicles have high requirements for road surfaces. This paper proposes and designs an amphibious disaster relief vehicle. This paper mainly combines the hovercraft with ...[Details]
1 Introduction
Variable frequency power supply is a power conversion device, which has the advantages of pure output waveform, stable output voltage, adjustable output frequency and output v...[Details]
Abstract: Currently, medium and small power switching power supplies are developing towards monolithic integration. This article elaborates on the performance characteristics and typical applicat...[Details]