PIC16CR84A-10I/P datasheet, PDF

Datasheet> All Categories > semiconductor> The embedded processor and controller> PIC16CR84A-10I/P

PIC16CR84A-10I/P: Description8-BIT, FLASH, 4 MHz, RISC MICROCONTROLLER, PDSO18; Categorysemiconductor The embedded processor and controller; File Size37KB，4 Pages; ManufacturerMicrochip; Websitehttps://www.microchip.com

Download Datasheet Parametric View All

PIC16CR84A-10I/P Overview

8-BIT, FLASH, 4 MHz, RISC MICROCONTROLLER, PDSO18

PIC16CR84A-10I/P Parametric

Parameter Name	Attribute value
Number of functions	1
Number of terminals	18
Maximum operating temperature	85 Cel
Minimum operating temperature	-40 Cel
Maximum supply/operating voltage	6 V
Minimum supply/operating voltage	2 V
Rated supply voltage	5 V
External data bus width	0.0
Number of input and output buses	13
Line speed	4 MHz
Processing package description	0.300 INCH, PLASTIC, SO-18
Lead-free	Yes
EU RoHS regulations	Yes
China RoHS regulations	Yes
state	ACTIVE
Craftsmanship	CMOS
packaging shape	RECTANGULAR
Package Size	SMALL OUTLINE
surface mount	Yes
Terminal form	GULL WING
Terminal spacing	1.27 mm
terminal coating	MATTE TIN
Terminal location	DUAL
Packaging Materials	PLASTIC/EPOXY
Temperature level	INDUSTRIAL
Address bus width	0.0
Number of digits	8
Maximum FCLK clock frequency	4 MHz
Microprocessor type	RISC MICROCONTROLLER
ROM programming	FLASH

Preview

Download Datasheet

View All

PIC16F83

PIC16F83 Rev. A Silicon Errata Sheet

The PIC16F83 (Rev. A) parts you have received conform

functionally to the Device Data Sheet (DS30430

except for the anomalies described below.

All the problems listed here will be addressed in future

revisions of the PIC16F83 silicon.

Module: CPU (STATUS bit)

The operation of the power-down (PD) bit in the STA-

TUS register may not function correctly for tempera-

tures below - 20 ˚C.

Work Around

None

Module: Data EEPROM

Do not perform a modify (set or clear a bit) of the

EECON1 register one instruction cycle after an

EEPROM read. This will corrupt the EEDATA regis-

ter.

Example:

BSF

BCF

EECON1, RD

EECON1, WREN

Module: Timer0

The TMR0 register may increment when the WDT

postscaler is switched to the Timer0 prescaler. If

TMR0 = FFh, this will cause TMR0 to overﬂow (set-

ting T0IF).

Work Around

Follow the following sequence:

Read the 8-bit TMR0 register into the W register

Clear the TMR0 register

Assign WDT postscaler to Timer0

Write W register to TMR0

Work Around

Use either of the following two code segment in place

of the above example.

BSF

NOP

BCF

EECON1, RD

EECON1, WREN

BCF

BSF

EECON1, WREN

EECON1, RD

Note:

As with any windowed EPROM device, please cover the window at all times, except when erasing.

1998 Microchip Technology Inc.

DS30430C/F83/E1A1-page 1

Recommended Resources

SHD106 type two feed water pumps, one in use and one in standby, automatically rotate and start at full pressure, and the standby pump current controls the self-throwing (pool) circuit a

Relaxation oscillator circuit composed of unidirectional thyristor

Nickel-cadmium battery pack automatic charger circuit

Satellite receiver MAC interface circuit

DT-1 type 3 1/2 digit digital multimeter circuit

Stationary switch with integrated trigger TDAl024

Use the C language library setjmp/longjmp function for exception recovery: A long time ago, when I was still using Turbo C 2.0 to write programs, I saw setjmp() and longjmp() functions when browsing library functions in the help function, but I never understood what they wer...; cruelfox MCU

28027FLASH cannot be programmed, and the program is not saved after power failure in DEBUG: I used C2000TMS320F28027F and CCS10.1 software. After right-clicking the project's PROPERTIES, I set the BUILD release and then clicked DEBUG. It showed that the download was complete and I could debu...; jhyzero Microcontroller MCU

Optimized spacer electric field analysis port 1 to 2 after learning: [i=s]This post was last edited by btty038 on 2021-7-28 22:06[/i]...; btty038 RF/Wirelessly

EEWORLD University ---- TI GaN-based high-frequency (1.2MHz) high-efficiency 1.6kW high-density critical mode (CrM) totem pole power factor correction (PFC) converter application introduction: Application introduction of TI's GaN-based high-frequency (1.2MHz), high-efficiency, 1.6kW, high-density critical mode (CrM) totem pole power factor correction (PFC) converter : https://training.eewor...; hi5 Integrated technical exchanges

Wave animation: Square wave edge jitter waveformAM and FM signalsPWM Control LED BrightnessPhase Modulated Signal...; btty038 RF/Wirelessly

Breaking News | Tesla's self-developed new battery heat ignites the market: This content is originally created by EEWORLD forum user chongdianzhuang . If you want to reprint or use it for commercial purposes, you must obtain the author's consent and indicate the sourceAccordi...; chongdianzhuang Automotive Electronics

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components