Standard Frequencies – see Page 5 for common frequencies.
* Check with factory for availability of frequencies not listed.
Applications
IoT and IIoT Applications
Wireless Communications
FPGA/Microcontrollers
USB Interfaces
Computer Peripherals
Portable Equipment
Test and Measurement
M2M Communications
Broadband Access
Description
CTS Model 407 incorporates a high Q quartz resonator and is ideal for supporting a wide range of commercial and
industrial applications.
Ordering Information
Model
407
Mode of
O s ci l l a ti on
F
Tol era nce
@ +25°C
3
Tem pera ture Sta bi l i ty/Tem pera ture Ra ng e
5
Loa d
Ca pa ci ta nce
D
F requency
[ MHz ]
XXXMXXXX
Mode
Code
Fundamental
F
3rd Overtone
T
Code
- 20°C
1
X
2
3
5
Code
1
X
2
3
Tolerance
±10ppm
±15ppm
±20ppm
±30ppm
Stability Code
to +70°C - 30°C
±10ppm
R
±15ppm
Y
±20ppm
N
±30ppm
4
±50ppm
8
Stability Code
to +85°C - 40°C
±10ppm
-
±15ppm
W
±20ppm
6
±30ppm
7
±50ppm
9
Stability
to +85°C
-
±15ppm
±20ppm
±30ppm
±50ppm
Code
Frequency
1
Frequency
Code Capacitance Code Capacitance
8pF
18pF
K
D
9pF
20pF
J
E
10pF
24pF
A
F
12pF
30pF
L
G
16pF
Series
C
S
Notes:
1] Frequency is recorded with 3 leading digits before the "M" and 4 significant digits after the "M" [including zeroes]. (Ex. XXXMXXXX [016M3840],
There are frequencies with significant digits after the "M" that exceed the 4 digits. The remaining digits will be truncated from the CTS part
number, but the factory will calibrate to the full frequency desired. Examples below; P/N Frequency = Actual Frequency
13M5537 = 13.553750MHz
14M3181 = 14.318180MHz
16M6666 = 16.666670MHz
28M6363 = 28.636360MHz
N ot a l l perf orm a nce com bi na ti ons a nd f requenci es m a y be a va i l a bl e.
Conta ct your l oca l CTS Repres enta ti ve or CTS Cus tom e r Servi ce f or a va i l a bi l i ty.
This product is specified for use only in standard commercial applications. Supplier disclaims all express and implied warranties and liability in connection with any use of this
product in any non-commercial applications or in any application that may expose the product to conditions that are outside of the tolerances provided in its specification.
It almost ended badly, haha, luckily lemon brother @nmg has been following it, which gave me some motivation to start. Well, I won’t say much, if you are not clear, you can read the previous posts:
[1...
I have a batch of equipment that is used for driving school timing with Nuc972 + STM32. I customized it for the driving school before, and I made a part of it too much. I don’t want to leave it to gat...
When designing hardware circuits, you will often encounter TYPE-C application designs. Attached is some of the information I compiled. I hope it will be helpful to friends in need!...
Unboxing and sharing of learning experience
1. Thanks to EEWORLD for providing the evaluation opportunity, which allows us to get close to the latest TI products.
Evaluation finalists: Chuanglong TL57...
1 Hardware AppreciationIt has been a week since I got the board, but I was busy at work before the Mid-Autumn Festival and didn't have time to take a good look at the board's resources. Today, let's t...
GaN is so popular now that people seem to forget that GaN is still a relatively new technology, still in its early stages of development, with great potential for improvement and room for perfection. ...
DIY/Open Source Hardware
京公网安备 11010802033920号
EEWORLD
