EEWORLDEEWORLDEEWORLD

Part Number

Search

GUB-GM7ALF-02-3881-B-

Description
Array/Network Resistor, Isolated, Thin Film, 0.16W, 3880ohm, 0.1% +/-Tol, -50,50ppm/Cel, 3922,
CategoryPassive components    The resistor   
File Size493KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

GUB-GM7ALF-02-3881-B- Overview

Array/Network Resistor, Isolated, Thin Film, 0.16W, 3880ohm, 0.1% +/-Tol, -50,50ppm/Cel, 3922,

GUB-GM7ALF-02-3881-B- Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid795834399
package instructionSMT, 3922
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL6.2
structureMolded
JESD-609 codee3
Network TypeIsolated
Number of terminals14
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height2.286 mm
Package length9.906 mm
Package formSMT
Package width5.588 mm
Rated power dissipation(P)0.16 W
resistance3880 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesGUB
size code3922
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Terminal surfaceMatte Tin (Sn)
Tolerance0.1%
TaNFilm
®
Small Outline Surface
Mount Resistor Network
GUB Series
Thin film on ceramic technology
0.220” and 0.300” sizes available
RoHS compliant version available
DESC 87012 and 87013 available
Standard JEDEC packages for automatic placement equipment
Compliant leads to
compensate for
thermal expansion
and contractions.
IRC Advanced Film Division
Ultra precision tantalum
nitride resistance element
on high purity alumina.
Rugged, molded
construction.
IRC’s TaNFilm®, Small Outline Integrated Circuit resistor networks are ideally suited for surface mounting.
The 0.05 inch lead spacing provides higher lead density, increased component count, lower installed resistor
cost, and better reliability. They are ideally suited for the latest surface mount assembly techniques, and each
lead can be 100% visually inspected. The compliant leads relieve thermal expansion and contraction stressed
created by soldering and temperature excursions.
The tantalum nitride film system provides precision tolerance, exceptional TCR tracking, and low noise.
TaNFilm® provides stability, high reliability, and long life characteristics. Testing has demonstrated performance
exceeding MIL-PRF-83401 characteristics H.
Electrical Data
GM Type
Resistance Range (Ω)
GL Type
Absolute Tolerance
Ratio Tolerance To R1
TCR (ppm/°C)
TCR Tracking To R1 (ppm°C)
Operating Temperature Range
Noise
Substrate
Custom circuits and special testing available.
Schem A: 10 to 200K
Schem B: 10 to 1000K
Schem A: 10 to 150K
Schem B: 10 to 75K
Available to ±0.1%
Available to ±0.05%
±25, ±50, ±100
±5
-55°C to +125°C
Less than -25 dB
High purity alumina substrate
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
GUB Series Issue November 2008 Sheet 1 of 3
[RISC-V MCU CH32V103 Review] First impression of CH32V103C8T6 chip
After getting the RISC-V core development board sent by EEWORLD, I first did an experiment to light up the LED. It was basically smooth and I could see the LED flashing normally. This shows that the c...
bigbat Domestic Chip Exchange
100 check items for PCB design to ensure you have no problems with your design!
1. Data input stage1. Whether the data received in the process is complete (including: schematic diagram, *.brd file, bill of materials, PCB design instructions and PCB design or change requirements, ...
嘉立创创创 PCB Design
How to write the corresponding program process according to the timing diagram
I just got a chip. For commonly used chips, you can refer to the routines on the Internet for in-depth understanding. For an uncommon chip, the Datasheet is almost the only information for using the c...
fish001 Microcontroller MCU
Differences and similarities between detection circuits, filter circuits, frequency selection circuits, threshold comparison circuits, and bandpass circuits
The differences and similarities between detection circuits, filter circuits, frequency selection circuits, threshold comparison circuits, and bandpass circuitsI have been studying circuits for so lon...
QWE4562009 MCU
When designing PCB, how to consider electromagnetic compatibility EMC/EMI, specifically...
[size=4][b]Question[/b][/size] [size=4]How to consider electromagnetic compatibility (EMC/EMI) when designing PCB? What specific aspects should be considered? What measures should be taken? [/size]...
ohahaha PCB Design
How to measure the PWM generated by msp430f149 with an oscilloscope
I connected the red test lead to pin 46 (the pin that generates PWM) and the black test lead to gnd on the board, but the oscilloscope did not display a waveform and the PWM indicator light was flashi...
q胡= TI Technology Forum

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号