EEWORLDEEWORLDEEWORLD

Part Number

Search

C054362JX7R1LF

Description
Array/Network Capacitor, 100V, X7R, 0.0036uF, Through Hole Mount, SIP-5, SIP, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size94KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

C054362JX7R1LF Overview

Array/Network Capacitor, 100V, X7R, 0.0036uF, Through Hole Mount, SIP-5, SIP, ROHS COMPLIANT

C054362JX7R1LF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid1250644264
package instructionSIP,
Reach Compliance Codecompliant
capacitance0.0036 µF
Capacitor typeARRAY/NETWORK CAPACITOR
length13.97 mm
Installation featuresTHROUGH HOLE MOUNT
negative tolerance5%
Network TypeBUSSED C NETWORK
Number of components4
Number of functions1
Number of terminals5
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
encapsulated codeSIP
Package shapeRECTANGULAR PACKAGE
positive tolerance5%
Rated (DC) voltage (URdc)100 V
Maximum seat height7.62 mm
surface mountNO
Temperature characteristic codeX7R
Temperature Coefficient15% ppm/°C
Terminal pitch2.54 mm
Terminal shapeFLAT
width3.3 mm
Single-In-Line Conformal
Coated Capacitor Networks
C Series
·
·
Isolated or bussed circuits
4 to 14 Leads
Electrical
Rated Voltage
Capacitance Range
Tolerance
Temperature Coefficient
(% of Change)
Operating Temperature Range
J Tol.
±5%
K Tol.
±10%
M Tol.
±20%
25Vdc, 50Vdc, 100Vdc
10pF to 1μF (Custom 2.2pF to 10pF max.)
Z Tol.
+80% to -20%
Refer to Dielectric Table
CG & X7R: -55°C to +125°C
Y5V: -30°C to +85°C
Dielectric Table
Dielectric
X7R
Y5V
CG (NPO)
Specifications subject to change without notice.
Characteristics
±15% (-55 to +125°C)
+22% to -82% (-30 to +85°C)
±30ppm/°C
Values
1000pF to 1μF
100nF to 1μF
100pF to 1μF
General Note
TT electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT electronics’ own data and is considered accurate at time of going to print.
www.bitechnologies.com www.irctt.com www.welwyn-tt.com
© TT electronics plc
03.12
FPGA Design Process
FPGA Design Process...
zxopenljx EE_FPGA Learning Park
Power supply obstacles + power supply SBC selection and pitfalls
Hello everyone, I am an automotive electronics hardware engineer. When selecting a power SBC, you should pay attention to the battery voltage range and then combine it with the test standards to selec...
你好再见 Power technology
Sharing of key points on the use of ADI passive components
Sharing of key points on the use of ADI passive components...
勤奋 ADI Reference Circuit
Four design considerations for telematics hardware in connected cars
It may surprise you to learn that a technology that has been around for nearly two decades has paved the way for connected cars. ECall is old fashioned by high-tech standards, but it is now mandatory ...
alan000345 TI Technology Forum
Wide voltage input USB-C, 5V/3A output adapter reference design
USB-C, DFP, 5V/3A output, 85-265VAC input, adapter, low cost reference designThe UCC28700 and TPS25810 are used to provide isolated 5 V at 3 A over the USB type C interface. The UCC28700 performs prim...
qwqwqw2088 Analogue and Mixed Signal
When the machine is turned off, the LDO output is normally 3V. Why does the voltage reach 3.5V after the machine is turned on? What is the reason?
When the machine is turned off, the LDO output is normally 3V. Why does the voltage reach 3.5V after the machine is turned on? What is the reason?...
QWE4562009 Integrated technical exchanges

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号