f = 75 MHz, Integration bandwidth = 900 kHz to 7.5 MHz.
Vdd_YY
f = 75 MHz, Integration bandwidth = 12 kHz to 20 MHz.
Vdd_YY
LVCMOS Output Characteristics
Output Low Voltage
VOL
–
–
10%
Vdd
Input Characteristics
Input High Voltage
Input Low Voltage
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
50
2
Startup Time
Enable/Disable Time
Resume Time
RMS Period Jitter
T_start
T_oe
T_resume
T_jitt
–
–
–
–
–
Peak-to-peak Period Jitter
T_pk
–
–
RMS Phase Jitter (random)
T_phj
–
–
–
–
–
–
87
–
–
–
–
1.8
–
12
14
0.5
1.3
–
–
–
30%
150
–
5
138
5
Jitter
3
3.3
25
30
0.9
2
1.4
2.3
ps
ps
ps
ps
ps
ps
ps
ps
Vdd
Vdd
k
M
ms
ns
ms
Startup and Resume Timing
Table 2. Pin Description
Pin
Symbol
Output Enable
1
OE/ST /NC
̅ ̅̅
Functionality
H
[1]
: specified frequency output
L: output is high impedance. Only output driver is disabled.
H
[1]
: specified frequency output
L: output is low (weak pull down). Device goes to sleep mode. Supply
current reduces to I_std.
Any voltage between 0 and Vdd or Open
[1]
: Specified frequency
output. Pin 1 has no function.
Electrical ground
Oscillator output
Power supply voltage
[2]
OE/ST /NC
̅ ̅̅
Top View
VDD
Standby
No Connect
2
3
4
GND
OUT
VDD
Power
Output
Power
GND
OUT
Figure 1. Pin Assignments
Notes:
1. In OE or ST mode, a pull-up resistor of 10 kΩ or less is recommended if pin 1 is not externally driven. If pin 1 needs to be left floating, use the NC option.
̅ ̅̅
2.
A capacitor of value 0.1 µF or higher between Vdd and GND is required.
Rev 1.07
Page 2 of 18
www.sitime.com
SiT1602B
Low Power, Standard Frequency Oscillator
Table 3. Absolute Maximum Limits
Attempted operation outside the absolute maximum ratings may cause permanent damage to the part. Actual performance
of the IC is only guaranteed within the operational specifications, not at absolute maximum ratings.
Parameter
Storage Temperature
Vdd
Electrostatic Discharge
Soldering Temperature (follow standard Pb free
soldering guidelines)
Junction Temperature
[3]
Note:
3. Exceeding this temperature for extended period of time may damage the device.
Min.
-65
-0.5
–
–
–
Max.
150
4
2000
260
150
Unit
°C
V
V
°C
°C
Table 4. Thermal Consideration
[4]
Package
7050
5032
3225
2520
2016
JA, 4 Layer Board
(°C/W)
142
97
109
117
152
JA, 2 Layer Board
(°C/W)
273
199
212
222
252
JC, Bottom
(°C/W)
30
24
27
26
36
Note:
4. Refer to JESD51 for
JA
and
JC
definitions, and reference layout used to determine the
JA
and
JC
values in the above table.
Table 5. Maximum Operating Junction Temperature
[5]
Max Operating Temperature (ambient)
70°C
85°C
Maximum Operating Junction Temperature
80°C
95°C
Note:
5. Datasheet specifications are not guaranteed if junction temperature exceeds the maximum operating junction temperature.
Table 6. Environmental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Moisture Sensitivity Level
Condition/Test Method
MIL-STD-883F, Method 2002
MIL-STD-883F, Method 2007
JESD22, Method A104
MIL-STD-883F, Method 2003
MSL1 @ 260°C
Rev 1.07
Page 3 of 18
www.sitime.com
SiT1602B
Low Power, Standard Frequency Oscillator
Test Circuit and Waveform
[6]
Vdd
Vout
Test Point
tr
80% Vdd
tf
4
Power
Supply
0.1 uF
1
3
2
15pF
(including probe
and fixture
capacitance)
50%
20% Vdd
High Pulse
(TH)
Period
Low Pulse
(TL)
Vdd
OE/ST Function
1 kΩ
Figure 2. Test Circuit
Note:
6.
Duty Cycle is computed as Duty Cycle = TH/Period.
Figure 3. Waveform
Timing Diagrams
90% Vdd
Vdd
Vdd
50% Vdd
[7]
Pin 4 Voltage
T_start
No Glitch
during start up
ST Voltage
T_resume
CLK Output
HZ
T_start: Time to start from power-off
CLK Output
HZ
T_resume: Time to resume from ST
Figure 4. Startup Timing (OE/ ST̅ Mode)
̅ ̅
Figure 5. Standby Resume Timing ( ST̅ Mode Only)
̅ ̅
Vdd
50% Vdd
OE Voltage
T_oe
Vdd
OE Voltage
50% Vdd
T_oe
CLK Output
HZ
T_oe: Time to re-enable the clock output
CLK Output
HZ
T_oe: Time to put the output in High Z mode
Figure 6. OE Enable Timing (OE Mode Only)
Note:
7.
Figure 7. OE Disable Timing (OE Mode Only)
SiT1602 has “no runt” pulses and “no glitch” output during startup or resume.
Thanks to WWWORLD, I received the Pingtouge voice development kit. The box packaging is super gorgeous. The true appearance of the Xuantie 803c processor is as follows:The core board of the developmen...
The LMS ( least mean square ) algorithm has been widely used in the fields of adaptive filters, adaptive antenna arrays, etc. due to its fast convergence speed and simple algorithm implementation. In ...
[color=#333333][font="][size=14px]Aluminum electrolytic capacitors are commonly used to filter and store power supply voltages. But how do you choose the capacitance of aluminum electrolytic capacitor...
FanySkill installation instructions for Allegro 16.617.2 version : https://training.eeworld.com.cn/course/5960FanySkill Installation Instructions For Allegro 16.617.2 VersionFanySkill integrates more ...
The source program of msp430 microcontroller is as follows:#include "bsp.h"
int main( void )
{float cap,capfirst,capfirst1;unsigned int Data_FDC;
// Stop watchdog timer to prevent time out reset
WDTCT...
USART, AD and GPIO temperature sensors:
Please be aware of:
1、ADC_RegularChannelConfig(ADC1,ADC_Channel_16,1,ADC_SampleTime_239Cycles5);
2、ADC_TempSensorVrefintCmd(ENABLE);
According...[Details]
Circuit diagram and troubleshooting experience of vehicle inverter 1. The main indicators of common vehicle inverter products on the market: input voltage: DC 10V~14.5V; output voltage: AC 200V~220V±...[Details]
For years, I have been thinking about the ultimate future of EDA. Companies like Oracle, SAP, and Dassault provide a large amount of supporting software infrastructure for enterprises, including p...[Details]
Description of the program:
This solution proposes a general embedded board-level support platform technology for the automotive electronics field. A specific design is proposed, and a board-l...[Details]
Beijing time, September 16 morning news, according to reports, including Tesla CEO Elon Musk (Elon Musk) and other technology giants, have said that self-driving cars will one day replace traditional...[Details]
Uses: Redraw regularly to form dynamic waveforms, such as temperature curves.
Idea: Just like the MCU timer interrupt, first turn on the timer and then write the execution code into the CMy56Dlg::O...[Details]
According to IDC data, global personal computer shipments in the fourth quarter were 67.2 million units, a year-on-year decrease of 28.1%. All manufacturers except Apple recorded double-digit percent...[Details]
Advantech's A-Connect theme seminar is about to start, modular computer innovation standard COM-HPC leads the performance transformation The development of the era of the Internet of Everything has...[Details]
1. Starting, self-locking and stopping control and circuit
Start, self-lock and stop control are the basic control functions of PLC. Start, self-lock and stop control can be realized by drive ...[Details]
Soitec, a global leader in the design and production of innovative semiconductor materials, announced a strategic collaboration with Mersen, a global expert in power and advanced materials, to jointl...[Details]
0 Introduction
With the rapid development of the microelectronics industry, intelligent controllers controlled by single-chip microcomputers are widely used in electronic products. In order to enabl...[Details]
New Field-Proven Sales Team to Drive Expansion in Asia Pacific February 16, 2022, Beijing, China - Morse Micro, a fabless semiconductor company reinventing Wi-Fi® for the Internet of Things (IoT), ...[Details]
Microsoft offers excellent products under its Surface brand, such as Surface Duo and Surface Book. According to recently published patent details, Microsoft is now developing the next generation...[Details]
3. In the board, in order to verify whether the new u-boot is available, you need to set the IP address in u-boot first, as shown below: Pay attention to the red words below U-Boot 1.1.6 (Dec 5 2009...[Details]
Find X8 Pro will be equipped with the industry's only dual periscope telephoto lens and the first inverted periscope camera.
The Find X8 series is the first to be equipped with AI ...[Details]