EEWORLDEEWORLDEEWORLD

Part Number

Search

GUB-GM8ALF-03-1321-C-F

Description
Array/Network Resistor, Isolated, Thin Film, 1.2W, 1320ohm, 0.25% +/-Tol, 25ppm/Cel, Surface Mount, 2244, DIP, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size493KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance  
Download Datasheet Parametric View All

GUB-GM8ALF-03-1321-C-F Overview

Array/Network Resistor, Isolated, Thin Film, 1.2W, 1320ohm, 0.25% +/-Tol, 25ppm/Cel, Surface Mount, 2244, DIP, ROHS COMPLIANT

GUB-GM8ALF-03-1321-C-F Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1076421348
package instructionSMT, 2244
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL6.5
Other featuresULTRA PRECISION
structureMolded
Component power consumption0.16 W
The first element resistor1320 Ω
JESD-609 codee3
Manufacturer's serial numberGUB
Installation featuresSURFACE MOUNT
Network TypeISOLATED
Number of components1
Number of functions8
Number of terminals16
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height2.286 mm
Package length11.176 mm
Package shapeRECTANGULAR PACKAGE
Package formSMT
Package width5.588 mm
Rated power dissipation(P)1.2 W
Rated temperature70 °C
resistance1320 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesGUB
size code2244
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Temperature coefficient tracking5 ppm/°C
Terminal surfaceMatte Tin (Sn)
Terminal shapeGULL WING
Tolerance0.25%
TaNFilm
®
Small Outline Surface
Mount Resistor Network
GUB Series
Thin film on ceramic technology
0.220” and 0.300” sizes available
RoHS compliant version available
DESC 87012 and 87013 available
Standard JEDEC packages for automatic placement equipment
Compliant leads to
compensate for
thermal expansion
and contractions.
IRC Advanced Film Division
Ultra precision tantalum
nitride resistance element
on high purity alumina.
Rugged, molded
construction.
IRC’s TaNFilm®, Small Outline Integrated Circuit resistor networks are ideally suited for surface mounting.
The 0.05 inch lead spacing provides higher lead density, increased component count, lower installed resistor
cost, and better reliability. They are ideally suited for the latest surface mount assembly techniques, and each
lead can be 100% visually inspected. The compliant leads relieve thermal expansion and contraction stressed
created by soldering and temperature excursions.
The tantalum nitride film system provides precision tolerance, exceptional TCR tracking, and low noise.
TaNFilm® provides stability, high reliability, and long life characteristics. Testing has demonstrated performance
exceeding MIL-PRF-83401 characteristics H.
Electrical Data
GM Type
Resistance Range (Ω)
GL Type
Absolute Tolerance
Ratio Tolerance To R1
TCR (ppm/°C)
TCR Tracking To R1 (ppm°C)
Operating Temperature Range
Noise
Substrate
Custom circuits and special testing available.
Schem A: 10 to 200K
Schem B: 10 to 1000K
Schem A: 10 to 150K
Schem B: 10 to 75K
Available to ±0.1%
Available to ±0.05%
±25, ±50, ±100
±5
-55°C to +125°C
Less than -25 dB
High purity alumina substrate
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
GUB Series Issue November 2008 Sheet 1 of 3
[Silicon Labs BG22-EK4108A Bluetooth Development Review] Part 3: Bluetooth-Soc Blinky Example Development Experience
[i=s]This post was last edited by jj1989 on 2022-1-23 22:51[/i]【Silicon Labs BG22-EK4108A Bluetooth Development Review】Part 3: Official Bluetooth-Soc Blinky Example Development Experience Preface Last...
jj1989 Development Kits Review Area
Analysis of the effect of resistance between the be electrodes of PNP transistors
As shown in the figure below, if there is no resistor R3, then when the voltage at point A (i.e. Vin) is greater than (VT1+Vbe), the PNP will be turned on. If resistor R3 is added now, the voltage on ...
shaorc Analog electronics
I want to do some math questions for the postgraduate entrance examination. Which postgraduate entrance examination tutor can explain the real questions in a detailed and easy-to-understand way?
I want to do some math questions for the postgraduate entrance examination. Which postgraduate entrance examination tutor can explain the real questions in a detailed and easy-to-understand way?...
深圳小花 Talking
Today's live broadcast: TI takes you to experience the interconnected and efficient smart home solutions
Live broadcast time This afternoon 14:00-15:00Live AgendaApplication of wireless MCU products in the smart home industry- Introduction to TI's products in the field of wireless MCU- Introduction to su...
EEWORLD社区 TI Technology Forum
How to scan keys on this triangular keyboard
[color=#333333][font=Arial]The bottom row is connected to GND, and the others are connected to IO. When scanning the keys, set the first row to 0, scan the first column, set the second row to 0, scan ...
holikey MCU
Circuit principle?
The newcomer took over an old circuit and did not understand the testing principles of the fixture. 1. CN1 and CN2 will be connected to the DGND of CN1_1 and CN2_2 respectively (the DGND of the fixtur...
hau30729 Power technology

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号