C078243JX7R1 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> capacitor> C078243JX7R1

C078243JX7R1: DescriptionArray/Network Capacitor, 100V, X7R, 0.024uF, Through Hole Mount, SIP-7, SIP, ROHS COMPLIANT; CategoryPassive components capacitor; File Size94KB，3 Pages; ManufacturerTT Electronics plc; Websitehttp://www.ttelectronics.com/; Environmental Compliance

Download Datasheet Parametric View All

C078243JX7R1 Overview

Array/Network Capacitor, 100V, X7R, 0.024uF, Through Hole Mount, SIP-7, SIP, ROHS COMPLIANT

C078243JX7R1 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	1250652439
package instruction	SIP,
Reach Compliance Code	compliant
capacitance	0.024 µF
Capacitor type	ARRAY/NETWORK CAPACITOR
length	19.05 mm
Installation features	THROUGH HOLE MOUNT
negative tolerance	5%
Network Type	BUSSED C NETWORK
Number of components	6
Number of functions	1
Number of terminals	7
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
encapsulated code	SIP
Package shape	RECTANGULAR PACKAGE
positive tolerance	5%
Rated (DC) voltage (URdc)	100 V
Maximum seat height	7.62 mm
surface mount	NO
Temperature characteristic code	X7R
Temperature Coefficient	15% ppm/°C
Terminal pitch	2.54 mm
Terminal shape	FLAT
width	3.3 mm

Preview

Download Datasheet

View All

Single-In-Line Conformal

Coated Capacitor Networks

C Series

Isolated or bussed circuits

4 to 14 Leads

Electrical

Rated Voltage

Capacitance Range

Tolerance

Temperature Coefficient

(% of Change)

Operating Temperature Range

J Tol.

±5%

K Tol.

±10%

M Tol.

±20%

25Vdc, 50Vdc, 100Vdc

10pF to 1μF (Custom 2.2pF to 10pF max.)

Z Tol.

+80% to -20%

Refer to Dielectric Table

CG & X7R: -55°C to +125°C

Y5V: -30°C to +85°C

Dielectric Table

Dielectric

X7R

Y5V

CG (NPO)

Specifications subject to change without notice.

Characteristics

±15% (-55 to +125°C)

+22% to -82% (-30 to +85°C)

±30ppm/°C

Values

1000pF to 1μF

100nF to 1μF

100pF to 1μF

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

03.12

Recommended Resources

Electric shaver motor drive circuit

Interface circuit between CMOS and THL

Using 55-chip transmit driver circuit

Low Ripple Power supply circuit

Use LM567 to make a 0.1Hz-500kHz signal source circuit

Computer motherboard circuit diagram 820 1_59

Analog Filter and Circuit Design Handbook: A very practical reference book on analog filters and circuit design.This manual is divided into 19 chapters, which analyze and discuss the design of various active and passive filters, computer-aided...; arui1999 Download Centre

SensorTile.Box Kit Operation Mode Programming Mode Trial: [i=s]This post was last edited by lvqy on 2020-5-19 17:24[/i] # Try programming mode# Download the development source code Downloaded the file: en.FP-SNS-STBOX1_firmware.zip After unzipping, the compi...; lvqy ST MEMS Sensor Creative Design Competition

Teach you how to design a power supply step by step: The whole process of power supply design [align=left]This time, a 13.2W power supply is taken as an example[/align][align=left]Input: AC90~264V[/align][align=left]Output: 3.3V/4A[/align][align=left][b...; okhxyyo Power technology

Boost circuit problem: I use USB power supply and want to increase the voltage to about 11V to power the OPA in the following circuit. Iencountered a very strange situation. After using FP6291 for a period of time (the time...; hau30729 Power technology

Use of TI DSP Integrated Development Environment CCS: CCS is an integrated development environment launched by TI for developing DSP chips. It uses a Windows-style interface and integrates editing, compiling, linking, software simulation, hardware debugg...; 火辣西米秀 DSP and ARM Processors

How to become an IC expert: How to become an IC design expert? How to improve your design ability? My feeling is that IC design is different from general board-level electronic design. Since the investment in tape-out is larger,...; soso FPGA/CPLD

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components