Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
Help: Does anyone have a SiliconLabs BRD4001A board? Can I borrow it?Can the JLink on this board debug other manufacturers' MCUs? For example, STM32? What is the speed?Can this board be recognized in ...
[i=s]This post was last edited by eagler8 on 2021-10-4 09:16[/i]I suddenly had the urge to do a series of topics on sound visualization. This topic is a bit difficult and covers a wide range of areas....
As discussed in Part 1, the analog sensor signal chain faces high-precision challenges: multiple gain, signal conditioning, and complex analog filtering stages, all feeding the SAR-ADC; thus, analog e...
6-Hardware I2C reads DHT12 dataAfter trying it for a while, I found that the CH582 library function is simple and convenient to use, and it is easy to get started. However, some routines are lacking, ...
Recently, Huawei has been exposing the news every day. Is it so difficult to send text messages using satellites?
Mobile phone positioning also uses satellite interactive information, and the messages...
The function used to generate random numbers in C++ is rand(), and its return value is an integer.
To generate a floating point number between 0 and 1, it must be converted.
Idea: Generate a random nu...
8031/8051/8751 are early products of Intel.
1. Characteristics of 8031
The 8031 chip does not have a program memory ROM. When using it, the user needs an external program memory and a logic cir...[Details]
1 Introduction
The single-chip microcomputer application system has the characteristics of simple structure, high reliability, strong flexibility, high performance-price ratio, etc., and has b...[Details]
1. Main structure 1) 16-bit adder counter , composed of high 8-bit (THi) and low 8-bit (TLi) SFR. 2) When used as a counter, pins P3.4 (T0) and P3.5 (T1) are the external pulse input terminals of...[Details]
Translated from eetimes In the realm of autonomous driving, the road to Level 4 and Level 5 self-driving cars is still long and tortuous. The delay in the release of self-driving cars by several ...[Details]
TVS diodes are essential high-efficiency protection components in the electronics industry and have been playing an indelible role in electronic products such as mobile phones, computers, and televis...[Details]
In the process of electronic system design and debugging, voltage measurement is often an indispensable item in the measurement and control or measurement system. For voltage measurement, if it chang...[Details]
Fiber optic interface type
Fiber optic connector
FC round with thread (mostly used on patch panels)
ST snap-on round type
SC snap-on square type (mostly used on routers and sw...[Details]
How to learn microcontrollers? I often see people say that they have studied for several months but have made no progress. Of course, due to the different education levels and personal understanding ...[Details]
It is not difficult to transform the basic TTL inverter into a multi-input NAND gate. Its main feature is the use of a multi-emitter BJT at the input of the circuit, as shown in the figure below. Each...[Details]
Product development Because of their non-contact temperature measurement capabilities, thermal imaging cameras have become an indispensable tool for a variety of research and development projects, an...[Details]
In
Filter
Wizards 12 (Filter Design Using the “Million Monkeys” Method), I gave myself an extra task, promising to go into depth on various filter design and network theory issues as I rushe...[Details]
The scale of photovoltaic projects is different, and the access voltage level is different. For example, below 8kW is generally connected to 220V, 8~400kW is generally connected to 380V, below 0.4~...[Details]
0 Introduction
With the continuous development of society and the emergence of smart devices, remote controls are becoming more and more widely used. Wireless remote controls have become more a...[Details]
The competitive advantages of Chinese power battery companies such as products and technologies have been recognized by international car companies, and Chinese battery companies have occupied the ma...[Details]
1. Introduction
The wave of new energy vehicles is getting bigger and bigger, and the body intelligence is becoming more and more perfect, and intelligent driving is closely related to sensors...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
