Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
[font=微软雅黑][size=3]I just graduated this year and joined my current company in October. When I first came in, within two days, they immediately gave me a project to do, and I was doing it all by mysel...
The importance and value of power density in modern power delivery solutions cannot be ignored. In order to better understand the basic techniques of high power density design, in this article, four i...
[i=s]This post was last edited by wangerxian on 2022-11-8 15:03[/i]The mobile phone does not have a wireless charging function. Without considering the size issue , is it feasible to use this kit to a...
[i=s]This post was last edited by zzzy11 on 2022-9-15 15:06[/i]The pot-shaped directional antenna stands on the roof, which can communicate with the orbiting satellite in the atmosphere 550 kilometers...
UART, I2C and SPI are the three most commonly used communication protocols in microcontroller systems. We have already learned about UART and I2C communication protocols. In this lesson, we will learn...
STM32 supports bit-band operation (bit_band), and bit-band is implemented in two areas. One is the lowest 1MB range of the SRAM area, and the second is the lowest 1MB range of the on-chip peripheral ...[Details]
The PIC programming program uses the official environment - MPLAB IDE v8.70: step: 1. Open MPLAB IDE v8.70 and import the HEX file firmware, as shown below: 2. Select the corresponding chip mo...[Details]
Before the popularization of reversing radar and rearview cameras, many experienced drivers were proud of their unique skills. Now, automatic parking has become the first application scenario for dri...[Details]
The online UPS synchronous phase-locked circuit is shown in the figure. It is composed of a crystal oscillator, a frequency divider, a synchronous signal selector, etc.
Figure 1. Online UPS sync...[Details]
According to foreign media reports, research shows that the use of electrolyte additives can extend the life of lithium metal batteries and significantly improve their fast charging and discharging p...[Details]
On October 18, Volkswagen Group and Canadian quantum technology company Xanadu established a multi-year research program to improve the performance of quantum algorithms used to simulate battery mate...[Details]
TPS61081 WLED backlight driver circuit
The WLED display backlight driver is shown in Figure 4. If the voltage feedback network is replaced by the WLED string and the series current sense resist...[Details]
Famous humanoid
robot
manufacturer Agility Robotics recently announced that veteran technology executive Peggy Johnson will serve as the company's CEO, replacing co-founder Damion Shelton. ...[Details]
Xinhua News Agency learned from the Ministry of Industry and Information Technology today (26) that the total shipments of the domestic mobile phone market in January 2020 were 20.813 million units, ...[Details]
0 Introduction
The portable field strength tester has high requirements for the first local oscillator phase noise. Its reference frequency is provided by the reference loop, so the phase noise...[Details]
WPG Group launches Bluetooth 5.1 hearing aid headset solution based on Audiowise products
On March 3, 2022, WPG Holdings, a leading semiconductor component distributor dedicated to t...[Details]
——Explain how graphics processing units (GPUs) and neural network accelerator chips provide intelligent advantages for automotive applications By Bryce Johnstone, Director, Automotive Products, Im...[Details]
The basic information required for motor selection includes: the type of load driven, rated power, rated voltage, rated speed, and other conditions.
1. Type of load driven
This has to b...[Details]
1 Introduction CAN bus is one of the popular bus technologies and a network based on microcontrollers. It uses an open, interoperable network to interconnect various controllers and instrumentation...[Details]
Everyone is familiar with 52 single-chip microcomputers, but few people use Timer2. There is little information in books and on the Internet. Here is an article to give you a preliminary understandin...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
