Ordering Information .................................................................................................................................................................... 2
7.1. User Programming Interface ..................................................................................................................................... 19
7.2. Start-up output frequency and signaling types .......................................................................................................... 19
8.1. Any-frequency function ............................................................................................................................................. 20
9 I C/SPI Control Registers...................................................................................................................................................... 30
9.1. Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 30
9.2. Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 31
9.3. Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 32
9.4. Register Address: 0x03. Flac-N PLL Integer Value and Flac-N PLL Fraction MSW ................................................. 33
9.6. Register Address: 0x05. PostDiv, Driver Control ...................................................................................................... 34
9.7. Register Address: 0x06. mDriver, Driver Control ...................................................................................................... 35
2
10 I C Operation ........................................................................................................................................................................ 36
2
10.1. I C protocol ............................................................................................................................................................... 36
2
10.2. I C Timing Specification ............................................................................................................................................ 38
2
10.3. I C Device Address Modes ....................................................................................................................................... 39
Dimensions and Patterns ........................................................................................................................................................... 46
Additional Information ................................................................................................................................................................ 47
Revision History ......................................................................................................................................................................... 48
Rev 0.91
Page 3 of 48
www.sitime.com
SiT3522
340 to 725 MHz Elite™ I
2
C/SPI Programmable Oscillator
1 Electrical Characteristics
PRELIMINARY
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
340.000001
340.000001
Typ.
–
–
Max.
725.000000
500.000000
Unit
MHz
MHz
Condition
LVDS and LVPECL output driver, factory or user
programmable, accurate to 6 decimal places
HCSL output driver, factory or user programmable, accurate to
6 decimal places
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-20
-20
-25
-50
First Year Aging
Operating Temperature Range
F_1y
T_use
–
-20
-40
-40
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
Duty Cycle
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
VIH
VIL
Z_in
DC
T_start
T_oe_hw
70%
–
–
45
–
–
–
–
–
–
±1
–
–
–
3.3
3.0
2.8
2.5
–
–
100
–
–
–
+20
+20
+25
+50
–
+70
+85
+105
Supply Voltage
3.63
3.3
3.08
2.75
–
30%
–
55
3.0
9.1
V
V
V
V
Vdd
Vdd
kΩ
%
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
OE pin
OE pin
OE pin, logic high or logic low
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1 -year aging at 25°C
Extended Commercial
Industrial
Extended Industrial. Available only for I C operation, not SPI.
2
st
Temperature Range
Input Characteristics – OE Pin
Output Characteristics
Startup and Output Enable/Disable Timing
T_oe_sw
–
–
11.8
µs
Rev 0.91
Page 4 of 48
www.sitime.com
SiT3522
340 to 725 MHz Elite™ I
2
C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
PRELIMINARY
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.10
–
94
63
–
30
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3V or 2.5V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B
T_jitt
–
0.22
0.075
0.23
0.09
1
0.260
0.085
0.325
0.095
1.6
ps
ps
ps
ps
ps
f = 622.08 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 622.08, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 622.08 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 622.08, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 622.08 MHz, Vdd = 3.3V or 2.5V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
89
67
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3V or 2.5V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
340
530
50
1.375
50
460
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.060
0.21
0.070
1
0.255
0.070
0.320
0.80
1.6
ps
ps
ps
ps
ps
f = 622.08 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 622.08 MHz, IEEE802.3-2005 10 GbE jitter mask
integration bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 622.08 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 622.08 MHz, IEEE802.3-2005 10 GbE jitter mask
integration bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 622.08 MHz, Vdd = 3.3V or 2.5V
mV
mV
V
mV
ps
f = 622.08 MHz. See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
With the rapid development of inertial navigation systems, gyroscopes, as the core of inertial navigation systems, determine the performance of inertial navigation systems. With the rapid development ...
Author: Wang Huidong, a member of Yibo Technology Expressway Media
If the circuit board is a person, then the drilling is its soul, especially the via, which is the soul of the board.In the design of ...
[i=s]This post was last edited by dcexpert on 2021-10-13 12:56[/i]To control, you need to choose the right button. There are two general types of buttons: self-locking and reset. Self-locking buttons ...
## 1. TopicIntroduction to cache operation interface of Allwinner F series/R series/V series RTOS platform
## 2. Problem BackgroundThe RTOS used by Allwinner F series/R series/V series provides some c...
List of enterprises that have obtained production qualifications in the tax control industry List of enterprises that have applied forproduction qualifications for tax control cash register products S...
[b]The Lunar New Year is approaching, good opportunities should not be missed. The current opportunities are all new positions opened before or after the holiday, and both the salary and company backg...
According to SK Hynix, the final acquisition of Intel's flash memory business still requires other regulatory approvals. Last Friday, SK Hynix officially announced that the acquisition of Intel's NAN...[Details]
The new USB Type-C® (USB-C) cable and connector specification greatly simplifies data interconnection and the way to power electronic products such as digital cameras and ultra-thin tablets (Figure...[Details]
Samsung said on Tuesday it has launched a second-generation security chip that can protect smartphones from software and hardware attacks and keep user data safe, The Korea Times reported. According ...[Details]
Apple releases a flagship phone at its annual autumn conference. There are four models in the series, iPhone 13mini, iPhone 13, iPhone 13 Pro, and iPhone 13Pro Max. The price of the small-screen mo...[Details]
According to the People's Daily, on the 17th, after receiving a letter of honor from party chairman Wu Dunyi at the Kuomintang Central Party Headquarters, Hon Hai Group Chairman Terry Gou announced h...[Details]
Today, we see more and more electronic products with USB Type-C™ and USB Power Delivery (PD) ports on the market. These products range from mobile phones, laptops and power banks to drones, power too...[Details]
At the OPPO Developer Conference, OPPO officially reviewed the technologies that ColorOS has opened to third parties. Let’s take a look: 1. System Album ColorOS was the first to open up the system ...[Details]
According to industry insiders, TSMC has launched its new advanced packaging technology - COUPE (compact universal photonic engine) heterogeneous integration technology for the data center market. "E...[Details]
In addition to the visual impact brought by high-definition video, the audio quality has also been greatly improved, which can bring you a more realistic on-site effect. So, what are the current ma...[Details]
There is a domestically produced MCU ne76e003 which is said to be able to be perfectly replaced pin to pin. Key information and prices Comparison of technical indicators between N76E003AT20 and S...[Details]
A study by the National Safety Council (NSC) shows that a workplace injury occurs every 7 seconds, which is equivalent to about 4.5 million injuries per year, which is a rather staggering statistic. ...[Details]
The printed circuit board layout determines the success or failure of any power supply, determining its function, electromagnetic interference (EMI), and performance under heat. Switching power s...[Details]
The Huawei Cloud Artificial Intelligence Summit Forum and the launch ceremony of the Shenfuxin District Artificial Intelligence Innovation Center, co-organized by the Liaoning Provincial Department o...[Details]
Currently, the relatively mature and widely used cathode materials for lithium-ion batteries are mainly lithium iron phosphate materials (LFP) and ternary lithium materials (NCM). From a performanc...[Details]
50 partners, 30 models, 28 applications: Intel Core Ultra processors (2nd generation) make AI accessible to all PC users
October 25, 2024, Beijing - Today,
Intel held the Intel Cor...[Details]