EEWORLDEEWORLDEEWORLD

Part Number

Search

ACS5LW213RA

Description
Fixed Resistor, Wire Wound, 5W, 213ohm, 400V, 0.05% +/-Tol, -20,20ppm/Cel
CategoryPassive components    The resistor   
File Size148KB,2 Pages
ManufacturerARCOL
Environmental Compliance
Download Datasheet Parametric View All

ACS5LW213RA Overview

Fixed Resistor, Wire Wound, 5W, 213ohm, 400V, 0.05% +/-Tol, -20,20ppm/Cel

ACS5LW213RA Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid1190684468
Reach Compliance Codecompliant
ECCN codeEAR99
structureCylindrical
Lead diameter1 mm
Lead length44 mm
Manufacturer's serial numberACS
Number of terminals2
Maximum operating temperature350 °C
Minimum operating temperature-55 °C
Package diameter8.52 mm
Package length22.5 mm
Package shapeCYLINDRICAL PACKAGE
Package formAxial
method of packingBulk; TR
Rated power dissipation(P)5 W
GuidelineMIL-R-39007
resistance213 Ω
Resistor typeFIXED RESISTOR
seriesACS
technologyWIRE WOUND
Temperature Coefficient20 ppm/°C
Tolerance0.05%
Operating Voltage400 V
ACS
Axial Coated Silicon Resistors
The design of the ACS resistor provides a good
balance of power density, stability and resistance to
environment for a broad range of industrial power
applications, such as drives and controls.
Good ratio between power capability and physical size
Wound to maximise high pulse capability
Low inductive versions available
Available on tape and reel or bulk
RoHS Compliant
Characteristics
Tolerance (Code):
Temperature coefficient:
Insulation resistance:
Dielectric withstand voltage:
MIL types:
A (±0.05%), B (±0.1%), F (±1%), G (±2%), J (±5%) and K (±10%)
<1R
±
90ppm/°C, 1R-10R
±50ppm/°C,
>10R
±
20ppm/°C
1, 000M ohms minimum dry, 100M ohms minimum after moiture test
500V AC
Available upon request.
Electrical Specifications
Type
ACS 1
ACS 2
ACS 3
ACS 5S
ACS 5L
ACS 7
ACS 10S
ACS 10L
Wattage
1
2
3
5
5
7
10
10
Max
working
voltage (V)
20
100
200
157
400
450
700
800
Resistance range
Inductive
(W)
R1 - 3K
R1 - 10K
R1 - 18K
R05 - 30K
R1 - 35K
R1 - 50K
R1 - 70K
R1 - 100K
Non Induc-
tive (N)
R1 - 1.5K
R1 - 4K
R1 - 9K
N/A
R1 - 17K
R1 - 25K
R1 - 35K
R1 - 50K
Derating Curve
100
80
Rated load %
60
40
20
0
0
25
50
75
100 125 150 175 200 225 250 275 300 325 350
Temperature ˚C
ACS 1 -
ACS 10L
ACS 5S
Ordering Procedure
Standard Resistor To specify standard: Series, Wattage Rating,
Winding Type, Resistance and Tolerance Code,
e.g.: ACS3 W 18K F
Tolerance (Code) ±0.05% (A), ±0.1% (B), ±1% (F), ±2% (G),
±5% (J), ±10% (K)
Typical Inductance
Type
ACS 1 - ACS2
ACS 3 - ACS5L
ACS 7 - ACS 10L
<50 ohms
0.2µH
0.3µH
0.65µH
>50 ohms
0.37µH
0.6µH
1.2µH
As specified by MIL-R-39007. Max series inductance at 0.5MHz.
ARCOL UK Limited,
Threemilestone Ind. Estate,
Truro, Cornwall, TR4 9LG, UK.
T +44 (0) 1872 277431
F +44 (0) 1872 222002
E sales@arcolresistors.com
The information contained herein does not form part of
a contract and is subject to change without notice. Arcol
operate a policy of continual product development, therefore,
specifications may change.
It is the responsibility of the customer to ensure that the
component selected from our range is suitable for the intended
application. If in doubt please ask Arcol.
Page 1 of 2
4 / 06.01
www.arcolresistors.com
[NXP Rapid IoT Review] Development Device and Online Programming Experience
[align=left]·When I received the development board, there was only a data cable and a [font=Calibri]sim[/font][font=宋体]card pin in addition to the host. The [/font][font=Calibri]sim[/font][font=宋体]car...
lxtwl RF/Wirelessly
TinyGo releases version 0.10.0
This release adds support for block selection, switches to LLVM 9, improves CGo support, and improves support for the ATSAMD51 ("M4") chip. It also adds support for a number of new boards: the Adafrui...
dcexpert MicroPython Open Source section
Introduction to the basics of photoresistors
1. Photoresistor A photoresistor is a special resistor made of semiconductor materials such as sulfide or selenide. The surface is also coated with moisture-proof resin and has a photoconductive effec...
fish001 Analogue and Mixed Signal
The role of negative pressure in LCD screens
In daily work, we occasionally encounter customer feedback: the LCD screen does not display or displays very light after it is turned on. The impact of voltage on this problem is often ignored by us. ...
罗姆液晶技术站 Integrated technical exchanges
5 points to note when using PCB reverse technology
In the study of PCB reverse technology, reverse deduction schematic refers to the reversal of PCB file diagram or drawing PCB circuit diagram directly according to the physical object of the product, ...
中信华 PCB Design
Differences between SMBus and I2C
[size=4]Differences between SMBus and I2C[/size] [size=4] [/size] [size=4] There are some differences in timing characteristics between SMBus and I2C buses. First, SMBus requires a certain data hold t...
灞波儿奔 Wireless Connectivity

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号