177-714-2-31GP4J5-24BCG datasheet, PDF

Datasheet> All Categories > The connector> The connector> 177-714-2-31GP4J5-24BCG

177-714-2-31GP4J5-24BCG: DescriptionInterconnection Device; CategoryThe connector The connector; File Size436KB，4 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/

Download Datasheet Parametric View All

177-714-2-31GP4J5-24BCG Overview

Interconnection Device

177-714-2-31GP4J5-24BCG Parametric

Parameter Name	Attribute value
Maker	Glenair
Reach Compliance Code	compli
Connector type	INTERCONNECTION DEVICE
Base Number Matches	1

Preview

Download Datasheet

View All

MWDM Micro-D Shielded Cable Assemblies

Single-Ended or Double-Ended–These

easy-to-order cable

assemblies eliminate the need for expensive assembly

labor. 100% tested and ready for use.

Now With Twisted Pairs–No

need to create a procurement

speciﬁcation for Micro-D cables with twisted pairs. Glenair

177-740 cables are furnished with a full complement of

white/blue twisted pair wires.

Integral Shield Termination–The

connector shell has a

platform to accept Band-It shield termination bands. The

cable shield braid is attached directly to the connector.

Save Labor, Reduce Weight and Improve EMI Shielding with

Glenair’s Micro-D Shielded Cable Assemblies

Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s fully

shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-piece connector

shell and secured with a stainless steel

BAND-IT

® clamp. These pre-wired, 100% tested assemblies meet the

requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low shell-to-shell resistance.

Available with a variety of wire types and shields, Micro-D shielded assemblies can be ordered in any length, either

single-ended or “back-to-back”.

Ground Spring and EMI Shielding Effectiveness

– A gold-plated

stainless steel ground spring on the pin connector mating face offers

substantial improvement in EMI protection. The graphs compare

identical connectors tested with and without ground springs.

EMI Performance with Ground Spring

SHIELDING EFFECTIVENESS (DB)

100

1.00E+03

100

1.00E+03

EMI Performance without Ground Spring

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

FREQUENCY (Hz)

CAGE Code 06324/0CA77

Printed in U.S.A.

GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912

www.glenair.com

B-8

E-Mail: sales@glenair.com

Recommended Resources

How to learn circuit diagrams?

Microprocessor and LCD drive circuit

DC and DC converter circuit diagram using thyristor b

Using two thyristors to stabilize the power supply

555 simple transistor tester circuit

Circuit to widen VC0 frequency range

PHYTEC's imx8mplus development board review: We received the imx8mplus development board from PHYTEC for evaluation, and last time we had it up, everything was working fine. The official website comes with a paper document for rapid development,...; yijiu98 Toshiba Photorelays TLP3547 Review

[RVB2601 Creative Application Development] 4. Use RTC to record time: [i=s]This post was last edited by hehung on 2022-3-6 19:28[/i]PrefaceRTC is a good choice for recording time. It does not require an external clock chip and can also achieve the purpose of obtaining a...; hehung XuanTie RISC-V Activity Zone

A brief discussion on the bus differences of ARM Cortex-m0/m4 series: Let’s start with a simple question: How fast can the GPIO flip speed of STM32 (for example, used to simulate timing) be? Write a piece of code to test: [code]void test(void) { for(;;) { GPIOA->ODR = (...; cruelfox MCU

Please help me interpret this article about tl431 bias current: https://www.baidu.com/sf_edu_wenku/view/326acdef172ded630b1cb6b7 I don't know where the original post came from. . The first question. . Are α and β equal in the third equation? Otherwise, how did the...; grove_armweak Power technology

Disable automatic layer selection for routing: I would like to ask how to turn off the automatic layer selection function for routing... When I draw a 4-layer board, I select Signal Layer 1 or Signal Layer 2 for routing, but as soon as I click on ...; bluefox0919 PCB Design

[National Technology N32 MCU Development Package] --N32L40x Series: Tips: Go to the official website of National Technology - Developer Community - Download, and you can download the latest version continuously.[attach]605263[/attach][attach]]605259[/attach][attach]60...; milafan Domestic Chip Exchange

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components