EEWORLDEEWORLDEEWORLD

Part Number

Search

NAND512R3M3CZB5E

Description
IC,MIXED MEMORY,FLASH+SDRAM,BGA,149PIN,PLASTIC
Categorystorage    storage   
File Size200KB,22 Pages
ManufacturerSTMicroelectronics
Websitehttp://www.st.com/
Environmental Compliance
Download Datasheet Parametric View All

NAND512R3M3CZB5E Overview

IC,MIXED MEMORY,FLASH+SDRAM,BGA,149PIN,PLASTIC

NAND512R3M3CZB5E Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid107064862
Reach Compliance Codeunknown
ECCN codeEAR99
JESD-30 codeR-PBGA-B149
Memory IC TypeMEMORY CIRCUIT
Mixed memory typesFLASH+SDRAM
Number of terminals149
Maximum operating temperature85 °C
Minimum operating temperature-30 °C
Package body materialPLASTIC/EPOXY
encapsulated codeFBGA
Encapsulate equivalent codeBGA149,12X16,32
Package shapeRECTANGULAR
Package formGRID ARRAY, FINE PITCH
power supply1.8 V
Certification statusNot Qualified
Nominal supply voltage (Vsup)1.8 V
surface mountYES
Temperature levelOTHER
Terminal formBALL
Terminal pitch0.8 mm
Terminal locationBOTTOM
NAND256-M
NAND512-M, NAND01G-M
256/512Mb/1Gb (x8/x16, 1.8/3V, 528 Byte Page) NAND
Flash Memories + 256/512Mb (x16/x32, 1.8V) LPSDRAM, MCP
PRELIMINARY DATA
Feature summary
Multi-Chip Packages
– 1 die of 256 Mb, 512 Mb (x8/ x16) NAND
Flash + 1 die of 256 Mb (x16) SDR
LPSDRAM
– 1 die of 256 Mb, 512 Mb (x8/ x16) NAND
Flash + 2 dice of 256 Mb (x16) SDR
LPSDRAMs
– 1 die of 256 Mb, 512 Mb (x8/ x16) NAND
Flash +1 die of 256 Mb (x16) DDR
LPSDRAM
– 1 die of 512 Mb (x16) NAND Flash + 1 die
of 256 Mb or 512 Mb (x16) DDR LPSDRAM
Supply voltages
– V
DDF
= 1.7V to 1.95V or 2.5V to 3.6V
– V
DDD
= V
DDQD
= 1.7V to 1.9V
Electronic Signature
ECOPACK
®
packages
Temperature range
– -30 to 85°C
FBGA
TFBGA107 10.5 x 13 x 1.2mm
TFBGA149 10 x 13.5 x 1.2mm
LFBGA137 10.5 x 13 x 1.4mm
Fast Block Erase
– Block erase time: 2ms (typ)
Status Register
Data integrity
– 100,000 Program/Erase cycles
– 10 years Data Retention
LPSDRAM
Interface: x16 bus width
Deep Power Down mode
1.8v LVCMOS interface
Quad internal Banks controlled by BA0 and
BA1
Automatic and controlled Precharge
Auto Refresh and Self Refresh
– 8,192 Refresh cycles/64ms
– Programmable Partial Array Self Refresh
– Auto Temperature Compensated Self
Refresh
Wrap sequence: sequential/interleave
Burst Termination by Burst Stop command and
Precharge command
Flash Memory
NAND Interface
– x8 or x16 bus width
– Multiplexed Address/ Data
Page size
– x8 device: (512 + 16 spare) Bytes
– x16 device: (256 + 8 spare) Words
Block size
– x8 device: (16K + 512 spare) Bytes
– x16 device: (8K + 256 spare) Words
Page Read/Program
– Random access: 12µs (max)
– Sequential access: 50ns (min)
– Page program time: 200µs (typ)
Copy Back Program mode
– Fast page copy without external buffering
May 2006
Rev 4
1/22
www.st.com
2
This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to
change without notice.
MSP430F5529 general I/O port settings
[size=4]Learn I/O first. I/O operation is the most basic, and these registers must be firmly mastered. The difficulty of MSP430 is that it has a large number of registers that need to be set. Although...
火辣西米秀 Microcontroller MCU
5 production processes that must be considered before PCB layout
[align=left][color=rgb(51, 51, 51)]When drawing PCB, we need to consider several issues clearly[/color][/align][list] [*][align=left]Single-layer board or double-layer board? [/align] [*][align=left]I...
okhxyyo PCB Design
I have to say that the old technology I have been exposed to since 2008 was still blocked at that time.
1-3. Input and output matching circuit The purpose of the matching circuit is to choose a way of acceptance. For those transistors that want to provide greater gain, the way is to accept and output it...
btty038 RF/Wirelessly
Calibration of medical devices
Calibration of medical devices 1. Thermometer calibration - use black body furnace + constant temperature water bath to calibrate two points 2. Sphygmomanometer calibration - using BP pump sphygmomano...
QWE4562009 Test/Measurement
Doesn't high input impedance mean high loss? Why does sampling require high input impedance? Low output impedance, such as running...
Doesn't high input impedance mean high loss? Why does sampling require high input impedance? Low output impedance, such as an op amp circuit...
QWE4562009 Integrated technical exchanges
How to set the prohibited routing area when AD wiring
I am using AD18. Where is the prohibited routing area set when routing? It appears every time I start routing, such as the area around the pad indicated by the arrow in the figure below. Thank you....
yyz1988 PCB Design

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号