Z/X/DZ Common Accessories
Common to Z, X, and DZ Models
Actuators (Sold Separately)
CSM_Z_X_DZ_OP_E_1_2
A Switch can be actuated by a cam or an appropriate object, in which case, use one of the following Actuators according to the application.
Ordering Information
Actuator
Hinge lever
Hinge roller lever
Short
Panel mount plunger
Medium
Long
Panel mount roller plunger
Application
Common to Z and X models
XAA-1
ZAA-2
ZAQ-3
ZAQ-2
ZAQ-1
ZAQ-22
Dimensions (Unit: mm) and Operating Characteristics
Hinge Lever
XAA-1
19.1
A-
1
XAA
-1
Note: These Actuators are not provided with Switches.
Two, M4
Two, M4 30
Model
Operating characteristics
Operating force OF max.
Release force
RF min.
Overtravel
OT min.
Movement Differential MD max.
Free Position
FP max.
Operating Position OP
OP
FP
Z-15G-B
4.90 N
1.67 N
12.7 mm
2.2 mm
X-10G-B
4.90 N
1.67 N
12.7 mm
3.3 mm
*
7
60R
XA
32.9±1.6 mm
28.9±1.6 mm
29.4
38.5
20.5
Note: This Actuator can be used with the Z-15G(-B) and X-
10G(-B). When mounting the Switch, set the overtravel to
between 32% and 100%, taking into consideration the
operating body and the distance between the Actuator
and the dog.
* Stainless steel
11.9
25.4±0.1
49.2
Two, M4 30
Hinge Roller Lever
ZAA-2
Two, M4
Z-15G-B
19.1
X-10G-B
4.90 N
1.67 N
12.7 mm
3.3 mm
22.2
*2
7
.5R
9.5 dia.
×
4.8 *1
OF max.
RF min.
OT min.
MD max.
FP max.
OP
4.90 N
1.67 N
12.7 mm
2.2 mm
58
44.5±1.6 mm
40.4±1.6 mm
OP
29.4
38.5
20.5
FP
Note: This Actuator can be used with the Z-15G(-
B) and ZX-10G(-B). When mounting the
Switch, set the overtravel to between 32%
and 100%, taking into consideration the
operating body and the distance between
the Actuator and the dog.
11.9
25.4±0.1
49.2
*1. Stainless steel roller
*2. Stainless steel
Short Panel Mount Plunger
ZAQ-3
PT
OP
1.6
*3
7.9 dia.
23.3
12SR
*1
M12
×
1 mounting
screw
2 t
×
14 width
across flats
17.5
2 t
×
15.6 width
across flats
22.6 24.2
Two, M4 nuts
ZAQ-3
Z-15E-B
OF max.
RF min.
PT max.
OT min.
MD max.
OP
8.34 N
1.12 N
0.8 mm
4.8 mm
0.15 mm
X-10G-B
5.39 N
1.12 N
1 mm
4.5 mm
0.2 mm
14.5
dia.
20.7
27.8±1.5 mm
*3
*2
13.5
25.4±0.1
52.4
20.7
*1. Stainless-steel pin plunger
*2. Bronze frame
*3. Incomplete screw section part with a maximum of 1.5 mm
Note: 1. This Actuator (pin plunger) can be used
with Standard Pin Plungers (Z-15G(-B),
Z-15E(-B), X-10G(-B), DZ-10G-1A(-1B))
for the Z, X, and DZ models.
Two, M4
×
25 screws
Note: Each dimension has a tolerance of
±0.4
mm unless otherwise specified.
1
Medium Panel Mount Plunger
PT
ZAQ-2
7.9 dia.
23.3
12SR
*1
M12
×
1 mounting screw
2 t
×
14 width across
flats
ZAQ-2
Z-15E-B
OF max.
RF min.
PT max.
OT min.
MD max.
OP
8.34 N
1.12 N
0.8 mm
4.8 mm
0.15 mm
X-10G-B
5.39 N
1.12 N
1 mm
4.5 mm
0.2 mm
OP
42.8
*3
14.5
dia.
2 t
×
15.6 width
across flats
1.6
53.2±1.5 mm
Two, M4
×
25 screws
20.7
22.6 24.2
Note: This Actuator (pin plunger) can be used with
Standard Pin Plungers (Z-15G(-B), Z-15E(-
B), X-10G(-B), DZ-10G-1A(-1B)) for the Z,
X, and DZ models.
*2
13.5
25.4±0.1
52.4
Two, M4 nuts
20.7
*1. Stainless-steel pin plunger
*2. Copper alloy frame
*3. Incomplete screw section part with a maximum of 1.5 mm
Long Panel Mount Plunger
PT
ZAQ-1
7.9 dia.
23.3
12SR
*1
M12
×
1 mounting screw
2 t
×
14 width across
flats
ZAQ-1
Z-15E-B
OF max.
RF min.
PT max.
OT min.
MD max.
OP
8.34 N
1.12 N
0.8 mm
20.6 mm
0.15 mm
X-10G-B
5.39 N
1.12 N
1 mm
20.4 mm
0.2 mm
OP
42.8
*3
14.5
dia.
2 t
×
15.6 width
across flats
69.1±1.5 mm
1.6
20.7
Note: This Actuator (pin plunger) can be used with
Standard Pin Plungers (Z-15G(-B), Z-15E(-
B), X-10G(-B), DZ-10G-1A(-1B)) for the Z,
Two, M4
×
25 screws
X, and DZ models.
22.6 24.2
*2
13.5
25.4±0.1
52.4
Two, M4 nuts
20.7
*1. Stainless-steel pin plunger
*2. Copper alloy frame
*3. Incomplete screw section part with a maximum of 1.5 mm
Panel Mount Roller Plunger
PT
ZAQ-22
48
23.3±0.25
12.7 dia. *1
4.8
Two hex nuts 5-mm
thickness, 19 mm
between opposing edges
With groove for roller
penetration
ZAQ-22
Z-15E-B
OF max.
RF min.
PT max.
OT min.
MD max.
OP
8.34 N
1.12 N
2 mm
3.58 mm
0.15 mm
37± 0.8 mm
DZ-10G-1B
11.1 N
1.12 N
2 mm
1 mm
0.46 mm
35.4±1.2 mm
OP
1.6
*3
14.5
dia.
18.9
M12
×
1 mounting
screw
20.7
23.9
Note: This Actuator (roller plunger) can be used with
standard pin plungers (Z-15G(-B), Z-15E(-B),
and DZ-10G-1A(-1B)). It cannot be used with
X models.
20.7
Spring washer
*2
11.9
25.4±0.2
49.2
Two, M4
×
25
screws
*1. Stainless-steel pin plunger
*2. Steel frame
*3. Incomplete screw section part with a maximum of 1.5 mm
Note: Each dimension has a tolerance of
±0.4
mm unless otherwise specified.
2
Read and Understand This Catalog
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or
comments.
Warranty and Limitations of Liability
WARRANTY
OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified)
from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR
FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS
DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED.
LIMITATIONS OF LIABILITY
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS
IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT
LIABILITY.
In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS
OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT
SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.
Application Considerations
SUITABILITY FOR USE
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's
application or use of the products.
At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the
products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product,
machine, system, or other application or use.
The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible
uses of the products, nor is it intended to imply that the uses listed may be suitable for the products:
•
Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog.
•
Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles,
safety equipment, and installations subject to separate industry or government regulations.
•
Systems, machines, and equipment that could present a risk to life or property.
Please know and observe all prohibitions of use applicable to the products.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE
SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
PROGRAMMABLE PRODUCTS
OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof.
Disclaimers
CHANGE IN SPECIFICATIONS
Product specifications and accessories may be changed at any time based on improvements and other reasons.
It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made.
However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or
establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual
specifications of purchased products.
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.
PERFORMANCE DATA
Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the
result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON
Warranty and Limitations of Liability.
ERRORS AND OMISSIONS
The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical,
typographical, or proofreading errors, or omissions.
2009.10
In the interest of product improvement, specifications are subject to change without notice.
Industrial Automation Company
http://www.ia.omron.com/
OMRON Corporation
(c)Copyright OMRON Corporation 2009 All Right Reserved.
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
