Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
SRIO error detection is mainly divided into two parts, physical layer error detection, logical layer / transport layer error detection, each error detection has a specific register to control. Physica...
[i=s]This post was last edited by qq849682862 on 2021-9-6 20:04[/i]Brand new RIGOL DC power supply, DP832 (three channels), all options are on, equivalent to the monochrome version DP832A ! You can al...
This month's insurance has not been paid yet. I asked my boss and he said it will be paid at the end of the month.Salaries are also paid at the end of the month. When asked why, he said he would get p...
[img]file:///C:\Users\Suqing\AppData\Roaming\Tencent\Users\1161848701\TIM\WinTemp\RichOle\()@}D}%KV00@P4$H)JORZ41.png[/img] Is there any difference between turning on and off the comment? Why can the ...
[i=s]This post was last edited by qwqwqw2088 on 2020-2-4 11:10[/i]Advantages of fiber optic communication ●Large communication capacity ●Long relay distance ●Not subject to electromagnetic interfer...
Comprehensive understanding of antennas, the knowledge you don’t know!
Antenna principles and RF passive device technology
Simulation research on high frequency antenna protection design
Several Bluet...
Impedance matching circuit composed of AD8228 integrated chip
Integrated circuit chips have high integration, low interference, good performance and small space. Therefore, the author selected the ...[Details]
0 Introduction
Cars are currently the main means of transportation for humans and a symbol of modern civilization. The annual sales of cars in the world reach more than 60 million, and the numb...[Details]
The controlled series compensation (TCSC) is the first FACTS device after the concept of flexible AC transmission system (FACTS) was proposed. Since TCSC is directly connected to the transmission l...[Details]
In Labview, we often encounter several concepts, namely, control references, property nodes, and local variables. What are the differences between them?
First, let's talk about refere...[Details]
Pointer multimeter is the most common multimeter. Different models of multimeters only have certain differences in the detection range and structure, but the detection functions are basically the sam...[Details]
Heat dissipation issues in class D amplifier design
When evaluating the performance of Class D amplifiers in the laboratory, continuous sine waves are often used as signal sources. Alt...[Details]
Xiaomi Mi 11 is here ahead of schedule! The pace is faster than we expected. Flagships are no longer regularly updated once a year. Manufacturers are rushing to enter the next stage ahead of schedule...[Details]
The demands on power supply designers are becoming higher and higher, and they are under tremendous pressure to improve efficiency, reduce costs, and shorten product development cycles. Power sup...[Details]
When environmental protection has become a national issue, in addition to traditional governance methods, how to scientifically use advanced technologies such as the Internet of Things, cloud computi...[Details]
After the release of Xiaomi 11, everyone has been looking forward to Xiaomi 11 Pro, and there have been more and more leaks about the phone recently. IT Home learned that today blogger @数码闲...[Details]
Recently, the first phase of the Chongqing Tongliang base of a world top 500 new energy enterprise was officially put into production, marking a leap forward for Chongqing's new energy storage industr...[Details]
In the past two years, with the rapid increase in the penetration rate of smart electric vehicles and the continuous increase in policies, the automotive braking system has begun to evolve rapidly to...[Details]
If a landline telephone is installed, the 50V DC voltage fed by the telephone line can be used to measure the voltage regulation value of the Zener diode below 40V. the way is; 1. Use a multimeter ...[Details]
Since it is still troublesome to develop under LINUX, is there a more convenient and simple development method under WINDOWS? The answer is yes. Of course, we cannot choose a development tool like ...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
