EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

355-1-039-1-F-RR0-0870

Description
Board Connector, 39 Contact(s), 1 Row(s), Male, Straight, 0.039 inch Pitch, Surface Mount Terminal
CategoryThe connector    The connector   
File Size1001KB,1 Pages
ManufacturerMPE-Garry GmbH
Download Datasheet Parametric View All

355-1-039-1-F-RR0-0870 Overview

Board Connector, 39 Contact(s), 1 Row(s), Male, Straight, 0.039 inch Pitch, Surface Mount Terminal

355-1-039-1-F-RR0-0870 Parametric

Parameter NameAttribute value
Objectid309012990
Reach Compliance Codecompliant
ECCN codeEAR99
Board mount optionsPEG
body width0.049 inch
subject depth0.106 inch
body length1.535 inch
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU
Contact point genderMALE
Contact materialCOPPER ALLOY
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Dielectric withstand voltage350VAC V
insulator materialTHERMOPLASTIC
Manufacturer's serial number355
Plug contact pitch0.039 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded1
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
PCB contact patternSTAGGERED
PCB contact row spacing4.3942 mm
Rated current (signal)1 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal pitch2.0066 mm
Termination typeSURFACE MOUNT
Total number of contacts39
Raspberry Pi Foundation Launches $4 Raspberry Pi Pico with MicroPython Support
Board SpecificationsThe Raspberry Pi Pico is a low-cost, high-performance microcontroller board with a flexible digital interface. Key features include:Raspberry Pi's RP2040 microcontroller chip, desi...
dcexpert MicroPython Open Source section
EEWORLD University ---- Overcurrent Sensing Technology
Overcurrent sensing technology : https://training.eeworld.com.cn/course/4986...
wanglan123 Analog electronics
[Zero-knowledge ESP8266 tutorial] Quick Start 23 Applying OLED
Quote:Now the outline of our electronic world is slowly emerging, but it is too empty, so we need to use small dots to fill this outline and make it gradually solid. These dots contain not only the el...
roc2 stm32/stm8
Why is 50 ohm impedance generally controlled in PCB design?
[align=left] In the process of PCB design, before routing, we usually stack the project we are going to design, and calculate the impedance according to the thickness, substrate, number of layers and ...
ohahaha PCB Design
SIMterix-Simplies~3~ Verilog-A
There are some limitations to using LTspice. When we want to simulate some mixed analog and digital scenarios, it is obviously not appropriate to use LTspice to create some logic. Although some simple...
xutong Analog electronics
C2000 Power-on Boot Mode Analysis
When using C2000, engineers often say that the chip simulation can run, but the stand-alone run cannot run; or when debugging, reset the chiprun, and find that the program cannot run. The main reason ...
Aguilera Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号