EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

FP-U8999-12-1061-Q-S-1

Description
Array/Network Resistor, Isolated, Thin Film, 0.025W, 1060ohm, 50V, 0.02% +/-Tol, -10,10ppm/Cel, 3925,
CategoryPassive components    The resistor   
File Size999KB,6 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

FP-U8999-12-1061-Q-S-1 Overview

Array/Network Resistor, Isolated, Thin Film, 0.025W, 1060ohm, 50V, 0.02% +/-Tol, -10,10ppm/Cel, 3925,

FP-U8999-12-1061-Q-S-1 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid795199948
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL7.2
Other featuresULTRA PRECISION
structureRectangular
Component power consumption0.025 W
The first element resistor1060 Ω
JESD-609 codee4
Installation featuresSURFACE MOUNT
Network TypeIsolated
Number of components1
Number of functions8
Number of terminals16
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height1.905 mm
Package length9.906 mm
Package formSMT
Package width6.35 mm
method of packingMAGAZINE
Rated power dissipation(P)0.025 W
Rated temperature70 °C
resistance1060 Ω
Resistor typeARRAY/NETWORK RESISTOR
Second/last element resistor1060 Ω
size code3925
surface mountYES
technologyTHIN FILM
Temperature Coefficient10 ppm/°C
Temperature coefficient tracking1 ppm/°C
Terminal surfaceGold (Au)
Terminal shapeFLAT
Tolerance0.02%
Operating Voltage50 V
AD PCB ad cannot be selected after copper coating, it is not a problem of which layer
I can't select the copper part after the ad is covered. I created it on the top layer and immediately selected it. I tried it on other layers, but they can't be selected after they are created. I can ...
示范法 PCB Design
About fatalerror in Modelsim simulation
ISE feels pretty good. Modelsim just prompts this. Is there any brother who can teach me?...
li617296559 FPGA/CPLD
Register Control of LMX2592
I use TI's LMX2592 chip to generate a 5G clock signal, and use FPGA to control its registers using the SPI method. The hardware is designed by myself, and the power supply of the chip is measured to b...
yangyang_l TI Technology Forum
Weekly highlights: 2018.9.3-9.9
[size=4]Hi, everyone~~I'm here again~~Guan Guan, the past week was very fulfilling and busy~~What kind of week did you just spend? Our forum has had a lot of good posts and exciting activities in the ...
okhxyyo Talking
[Fudan Micro FM33LG0 Series Development Board Review] LCD Usage and Truth Table Tool Instructions
[i=s]This post was last edited by AE007 on 2021-11-29 02:04[/i]This test is of FM33LG0 LCD module, and LCD truth table tool can be used to quickly define the display data register data corresponding t...
AE007 Domestic Chip Exchange
Renesas CPK-RA6M4 development board evaluation + ISL29035 light sensor reading data
After the last sharing, I was delayed by other things, so I continued to complete the task this time, mainly to test the onboard light sensor to obtain its value. The following is the method.First, ad...
流行科技 Renesas Electronics MCUs

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号