• Solder reflow temperature: +260°C max. for 10 seconds maximum
Packaging
• Supplied in tape and reel packaging, 2000 per reel
Irms
(2)
Amps
4.08
3.54
3.11
2.81
2.58
2.38
2.15
1.99
1.71
1.65
1.57
1.31
1.26
1.19
1.10
0.99
0.92
0.80
0.76
0.70
0.64
0.55
0.50
Isat
(3)
Amps
2.60
2.40
2.20
1.90
1.80
1.60
1.30
1.20
1.10
1.00
0.90
0.85
0.75
0.70
0.62
0.58
0.52
0.46
0.42
0.40
0.35
0.32
0.30
DCR
mΩ@20°C
(Typical)
13
18
23
28
33
39
48
56
76
82
90
130
140
157
185
226
263
343
385
517
608
817
1000
DCR
mΩ@20°C
(Maximum)
18
24
31
38
45
53
65
76
103
110
122
175
189
212
250
305
355
463
520
620
730
980
1200
K-factor
(4)
Description
• 125°C maximum total operating temperature
• Low profile surface mount inductors
• 6.0 x 6.0 x 3.0mm surface mount package
• Ferrite core material
• Shielded drum core reduces EMI
Part Number
Rated
Inductance
(µH)
2.7
3.3
4.2
5.0
5.8
7.8
10
12
15
18
22
27
33
36
44
52
68
82
100
120
150
180
220
OCL
(1)
µH ± 30%
2.7
3.3
4.1
4.9
5.8
7.8
9.3
11.3
14.1
17.1
20.4
26.0
32.4
34.4
44.0
52.0
65.6
81.6
94.4
110.1
144.5
175.7
210.9
SD6030-2R7-R
SD6030-3R3-R
SD6030-4R2-R
SD6030-5R0-R
SD6030-5R8-R
SD6030-7R8-R
SD6030-100-R
SD6030-120-R
SD6030-150-R
SD6030-180-R
SD6030-220-R
SD6030-270-R
SD6030-330-R
SD6030-360-R
SD6030-440-R
SD6030-520-R
SD6030-680-R
SD6030-820-R
SD6030-101-R
SD6030-121-R
SD6030-151-R
SD6030-181-R
SD6030-221-R
34
30
27
24
22
19
17
16
14
13
12
11
9.3
8.7
7.9
7.2
6.5
5.9
5.6
5.6
5.0
4.5
4.0
(1) Open Circuit Inductance Test Parameters: 100kHz, 0.1V, 0.0Adc.
(2) Irms: DC current for an approximate
∆T
of 40°C without core loss. Derating is necessary
for AC currents. Pad layout, trace thickness and width, airflow, and proximity of other heat
generating components will affect the temperature rise. It is recommended that the
temperature of the part not exceed 125°C under worst case operating conditions verified
in the end application.
(3) Isat amps peak for 35% rolloff (@25°C)
(4) K-factor: Used to determine B p-p for core loss (see graph).
B p-p = K*L*∆I, B p-p(mT), K: (K factor from table), L: (Inductance in µH),
∆I
(Peak to peak ripple current in amps).
(5) Part Number Definition: SD6030-xxx-R
SD6030 = Product code and size; -xxx = Inductance value in µH;
R = decimal point; If no R is present, third character = # of zeros.
-R suffix = RoHS compliant
1207
BU-SB07328
Page 1 of 3
Data Sheet 4314
Part Number
SD6030-271-R
SD6030-331-R
SD6030-391-R
SD6030-471-R
SD6030-561-R
SD6030-681-R
Rated
Inductance
(µH)
270
330
390
470
560
680
OCL
(1)
µH ± 30%
264.2
313.5
373.7
460.0
546.2
659.4
Irms
(2)
Amps
0.44
0.38
0.35
0.33
0.30
0.27
Isat
(3)
Amps
0.27
0.25
0.22
0.20
0.18
0.16
DCR
mΩ@20°C
(Typical)
1300
1733
2083
2250
2767
3458
DCR
mΩ@20°C
(Maximum)
1560
2080
2500
2700
3320
4150
K-factor
(4)
3.6
3.3
3.0
2.8
2.5
2.3
(1) Open Circuit Inductance Test Parameters: 100kHz, 0.1V, 0.0Adc.
(2) Irms: DC current for an approximate
∆T
of 40°C without core loss. Derating is necessary
for AC currents. Pad layout, trace thickness and width, airflow, and proximity of other heat
generating components will affect the temperature rise. It is recommended that the
temperature of the part not exceed 125°C under worst case operating conditions verified
in the end application.
(3) Isat amps peak for 35% rolloff (@25°C)
(4) K-factor: Used to determine B p-p for core loss (see graph).
B p-p = K*L*∆I, B p-p(mT), K: (K factor from table), L: (Inductance in µH),
∆I
(Peak to peak ripple current in amps).
(5) Part Number Definition: SD6030-xxx-R
SD6030 = Product code and size; -xxx = Inductance value in µH;
R = decimal point; If no R is present, third character = # of zeros.
-R suffix = RoHS compliant
Dimensions - mm
Top View
Bottom View
Front View
Recommended Pad Layout
Schematic
Left View
xxx = Inductance value in µH. R = decimal point. If no R is present third character = # of zeros.
wwllyy = Date code, R = Revision level.
Packaging Information
Supplied in tape and reel packaging,
2000 parts per reel, 13" diameter reel.
Core Loss
1
1MHz
0.1
Core Loss (W)
500kHz
300kHz
200kHz
100kHz
0.01
0.001
0.0001
1
10
Bp-p (mT)
100
1000
1207
BU-SB07328
Page 2 of 3
Data Sheet 4314
Temperature Rise vs. Loss
Inductance Characteristics
North America
Cooper Bussmann
1225 Broken Sound Parkway NW
Suite F
Boca Raton, FL 33487-3533
Tel: 1-561-998-4100
Fax: 1-561-241-6640
Toll Free: 1-888-414-2645
Cooper Bussmann
P.O. Box 14460
St. Louis, MO 63178-4460
Tel: 1-636-394-2877
Fax: 1-636-527-1607
Europe
Cooper Bussmann
Cooper (UK) Limited
Burton-on-the-Wolds
Leicestershire • LE12 5TH UK
Tel: +44 (0) 1509 882 737
Fax: +44 (0) 1509 882 786
Cooper Bussmann
Avda. Santa Eulalia, 290
08223
Terrassa, (Barcelona), Spain
Tel: +34 937 362 812
+34 937 362 813
Fax: +34 937 362 719
Asia Pacific
Cooper Bussmann
1 Jalan Kilang Timor
#06-01 Pacific Tech Centre
Singapore 159303
Tel: +65 278 6151
Fax: +65 270 4160
This bulletin is intended to present product design solutions and technical information that will help the end user with design applications. Cooper Bussmann reserves the right, without notice,
to change design or construction of any products and to discontinue or limit distribution of any products. Cooper Bussmann also reserves the right to change or update, without notice, any
technical information contained in this bulletin. Once a product has been selected, it should be tested by the user in all possible applications.
Life Support Policy: Cooper Bussmann does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the
Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling,
can be reasonably expected to result in significant injury to the user.
The circuit is as shown in the figure. B1 and B2 are 0~10V rising edge signals, C1 and C2 are corresponding output signals, and then C1 and C2 output Q through an OR gate (not shown in the figure). No...
DSP enforces byte alignment for char, short, and int, which means char is aligned by byte, int is aligned by 4 bytes, and short is aligned by 2 bytes. So when char* points to 0x1, using (int*)char* ac...
Cytech and ADI discuss with you: Gigabit digital isolators for video, converters, and communicationsClick to register
Various reports indicate that the digital isolation market will grow at more than ...
1. GPIO characteristics of TMS320C6748
Referring to the 1.2Features section of the TI technical document SPRUFL8B (TMS320C674x/OMAP-L1x Processor GPIO User's Guide), we can see that the GPIO of the TM...
Before making the "Wanli" Raspberry Pi car, the first step is to create a project repository. One is to record the process of making the car, and the other is to open source the whole process, and wel...
The common types of current probes on the market today are magnetic core current probes, or clip-on current probes. This is an indirect current detection technology in which the probe clamps the co...[Details]
IT Home learned that the Samsung Galaxy S20 series flagship new phone became the first smartphone to obtain USB Fast Charger certification. According to IT Home, to obtain USB Fast Charge ...[Details]
Single cable solution
The earliest technical solution for applying leakage cables to perimeter intrusion prevention systems only used a single leakage cable. The simplest system is formed ...[Details]
Everyone should be very familiar with true wireless Bluetooth headsets. Almost all mobile phone manufacturers are making similar products because they are convenient to use and are a very good access...[Details]
0 Preface
Due to the complex application environment, vast geographical area and other unfavorable working conditions, the speed control and related parameter monitoring of the switched relucta...[Details]
Introduction to 16-bit Advanced Control Timer (TIM1) The TIM1 of STM8S consists of a 16-bit auto-reload counter, which is driven by a programmable prescaler. In this chapter, i is used to represent 1...[Details]
Transformer capacity tester principle During the operation of the generator, the movement of the built-in coil needs to pass through the internal magnetic field, and then it can pass through the fixe...[Details]
An easily overlooked overflow problem in 8-bit microcontrollers
example:
uint16 wTmp ;
uint8 x ;
x=2;
wTmp = (uint16)(x*150);
Everyone, is there any problem with the above multiplication? ...[Details]
1. Accuracy of the instrument
China's electrical instruments are divided into seven levels: 0.1, 0.2, 0.5, 1.0, 1.5,
2.5, and 5.0
. This level means the percentage error of the full scale of t...[Details]
China Energy Storage Network:
Analysis and calculation methods for power system configuration energy storage
Dong Yu1, Fan Gaofeng1, Dong Cun1, Yu Ruoying2, Zhao Junyi3
(1. Stat...[Details]
According to foreign media reports, Guardian Optical Technologies announced that its sensors have added new safety features that can monitor the driver's eyelid opening (to determine whether there is...[Details]
Technical Principle of Ultrasonic Level Meter The ultrasonic level meter is installed on the top of the container. Under the control of the electronic unit, the probe emits a beam of ultrasonic pulse...[Details]
1. Limiting filter method (also known as program judgment filter method) A. Methods: Based on experience, determine the maximum deviation allowed between two samples (set to A). Every time a new val...[Details]
International Solar Photovoltaic Network News: Enphase Energy, Inc., a leading global supplier of solar microinverters, recently announced the launch of its seventh-generation Enphase IQ microinver...[Details]
October 16, 2024 -
In the wave of global digital transformation and the rise of big models, the global computing power industry is gradually shifting from being centered on computing units to b...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
