Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
[size=4][color=#000000][backcolor=white]1. The 555 chip can realize accurate timing function. In the delay mode, the external resistor and capacitor can realize relatively accurate timing. [/backcolor...
BOSS made the following request, giving up the solution. I am relatively unfamiliar with IPC, so I came to the forum to seek the opinions of forum friends. The requirements are as follows:
Note: IPC i...
The fixing of components on the printed circuit board is achieved by welding the leads to the pads. The function of the via is to connect the electrical connections at different levels. (1) The size o...
Figure 1 0~10V analog acquisition circuit based on ADS1115Figure 2 Effective resolution I would like to ask the forum masters, 1. 0~10V input, 1mv resolution required, is there a problem with my desig...
This time, we will use the combination of blynk app + server (local) + zero-knowledge ESP8266 development board to observe the temperature and humidity conditions obtained by ESP8266 through the mobil...
On October 28, BOE released its third-quarter report stating that from July to September 2021, the company achieved operating income of 55.993 billion yuan, a year-on-year increase of 46.77%, and net...[Details]
At this Shanghai Auto Show, Aptiv focused on ADAS system solutions, electrification technologies and solutions, as well as the next-generation smart car architecture SVA and open server platform O...[Details]
In the previous article, if you want to make the LED light up or the buzzer sound, you need to control the corresponding pins. But how can you use the program to control the level change of the pins?...[Details]
introduction
Based on the basic performance requirements of new energy vehicle drive motors, the commonly used drive motor types currently include three main categories, namely AC asynchronous...[Details]
Recently, WWT officially published a blog, introducing how WWT cooperated with Intel to use the Advanced Technology Center to demonstrate the new FPGA technology, making the entire FPGA development a...[Details]
When generating an exe program, how should the configuration files containing *** parameters, the database files of user information, and the report templates be handled? I require that the user can s...[Details]
Powerful clock interrupts
In the design of single-chip microcomputer programs, setting a good clock interrupt will enable one CPU to play the role of two CPUs, greatly facilitate and simplify t...[Details]
●The park has high energy consumption and large differences in energy demand, making the implementation of integrated energy services key.
●The deep integration of data and business enables 40...[Details]
Greenliant to Showcase Its Broad Industrial SSD Portfolio at Embedded World 2023
Highly reliable M.2, U.2 and 2.5" SSDs with capacities ranging from 10GB to 8TB will be on display
...[Details]
3.2 Addressing mode of ARM instructions The so-called addressing mode is the way the processor finds the physical address based on the address information given in the instruction. Currently, the ARM...[Details]
According to the "New Energy Vehicle Industry Development Plan (2021-2035)" issued by the State Council, by 2025, China's smart car sales will reach 20% of the total car sales that year, of which con...[Details]
Recently, foreign media TechDroider released a video, exposing a mobile phone suspected to be Redmi K30, which uses a punch-hole dual camera on the front and a vertically arranged three-camera on the...[Details]
This alliance enables both parties to provide unified products and services in enterprise-grade solutions to protect against ransomware attacks. January 15 , 2023 – Akamai Technologies, I...[Details]
The C8051F320 has a 10-bit successive approximation ADC that can operate in single-ended or differential mode.
1. Brief Principle
Two multiplexers are integrated in the microcontroller, whic...[Details]
introduction
The Attitude and Heading Reference System (AHRS) can provide attitude information such as heading, roll and rollover. High-precision inertial navigation devices such as mechanical...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
