CY3672
PTG Programming Kit
Features
• Supports Field-programmable Clock Generators
• CY2077FS, CY2077FZ, CY22050F, CY22150F,
CY22381F, CY22392F, CY22393F, CY22394F,
CY22395F, CY25100F, CY25200F, CY25701F,CY25702F
CY23FP12, CY26049, and CY27EE16
• Allows quick and easy prototyping
• Compact design for ease of portability
•
Easy to use Microsoft
®
Windows
®
95, 98, NT, 2K, ME,
XP-compatible interface
•
User-friendly CyberClocks™ or CyberClocks Online
software for JEDEC file development
Functional Description
The CY3672 programming kit enables any user with a PC to
quickly and easily program Field-programmable Clock Gener-
ators. The only set-up requirements are a power connection
and either a parallel port or USB port (CY3672-USB)
connection with the PC, as shown in
Figure 2.
Using CyClocksRT™, (embedded in CyberClocks software) or
CyberClocks Online, users can configure their parts to a given
specification and generate the corresponding JEDEC file. In
addition, CyClocksRT software provides PPM optimization
and power calculations.
The JEDEC file is then loaded into CY3672 software that
communicates with the programmer. The CY3672 software
has the ability to read and view the EPROM table from a
programmed device. The programming flow is outlined in
Figure 1.
CY3672-PRG Kit Contents
• Parallel port cable
• AC/DC adapter
• Quick start guide
• User manual
Set Up
Hardware
The CY3672 programming kit has a very simple set-up
procedure. As shown in
Figure 2,
only two connections are
required. The programmer must be connected to a PC through
either a parallel port or USB port (CY3672-USB) and must
receive power through the AC/DC adapter that gets hooked up
to your standard 110V/220V wall outlet. When using the
parallel port, make sure the parallel port settings on your
computer is ECP or EPP. CY3672-PRG or CY3672-USB are
the programming base unit that can be ordered separately with
any individual socket adapter.
CY3672-FTG Development Kit Contents in
Addition to CY3672-PRG Contents
• Three Sockets: CY3695, CY3698, CY3699
CY3672-USB Kit Contents in Addition to
CY3672-PRG Contents
• USB Driver CD ROM
• USB Cable
C y C lo c k s R T
C Y 3 6 7 2 S o ftw a re
P ro g ram m e r
C Y 36 72
A d a p ter
C y b e rC lo c k s O n lin e
Jedec
F ile
B it
S tre a m
Figure 1. Programming Procedure
Cypress Semiconductor Corporation
Document #: 38-07409 Rev. *F
•
198 Champion Court
•
San Jose
,
CA 95134-1709
•
408-943-2600
Revised October 31, 2005
CY3672
Wall
Power Adapter
PC with Parallel Port
Parallel Cable
CY3672
Adapter
Figure 2. CY3672 Programming Kit Set-up
Figure 2
is a close-up of the socket and illustrates the correct
orientation for placing the device into the socket. Pin1 should
always be in the lower left corner, as shown in
Figure 3.
CyberClocks Online, which is a web based software, is
available on-line through user registration. It configures
spread spectrum clock generators, such as CY25100.
To install the CY3672 software, first run SETUP.EXE to install
necessary DLLs to the windows registry. Once this is done,
run CY3672*.EXE to launch.
When the CY3672 programmer is used for the first time, it is
required to be in “TYPE” mode. This mode is set by pushing
the arrow keys on the programmer until you see “TYPE”
displayed on the LCD screen.
Software
Setting up the software is just as easy as setting up the
hardware. Download the latest revisions of CyberClocks and
CY3672 programmer software off of our web site at
www.cypress.com. To install CyberClocks, unzip the file, then
simply run the set-up file in the CyberClocks folder. It will
prompt the user for a few questions and then self-installs.
[1]
Figure 3. Device Orientation
Note:
1. Be sure to check for software updates at http://www.cypress.com/support.
Document #: 38-07409 Rev. *F
Page 2 of 6
CY3672
Quick Start Guide
Go through the following steps to properly configure and use
the CY3672.
1.
a. If you are using a parallel port, make sure your parallel
port setting is ECP or EPP in your PC Bios settings.
Connect the power supply and hook up the parallel port
to your computer and programmer.
b. If you are using a USB port, insert the drive files CD,
connect the power supply, and connect the USB cable
to the programmer and PC. The PC will detect the new
hardware, follow the wizard and search for suitable
driver from the CD-ROM.
c. Use the programmer arrow buttons to set the
programmer LCD display to “TYPE”
2.
a. Install CyberClocks or register on-line for SSCG
products configuration software, CyberClocks Online, at
www.cyberclocksonline.com
[2]
b. Install the CY3672 software, which is available on
Cypress website at www.cypress.com, onto your
computer.
3. Use CyberClocks or CyberClocks online to generate a
JEDEC file for the device you wish to program.
4. Open up the CY3672 software: go to Start
Menu->Programs->Cypress->CY3672 or the location
where the software was installed.
5. Double click on the device that you wish to program under
the CYPRESS->CyClocksRT menu on the left side of the
screen, see Figure 4.
6. Click on the “Start” button at the bottom of the popup
window, see Figure 5.
7. Browse to and select the JEDEC file which you created
earlier in step 4 and click on “Open”.
8. Click “Yes” when the Upload Message screen pops up.
9. Once you see “Complete...” on the status bar at the bottom
of the window click on the “Program IC” icon at the top right
of the window (see figure below).
10.When you see a window with “Socket 1... Program OK.”
pop up you have successfully programmed a device.
[3]
Step 10
Step 6
Figure 4. CY3672 Software, Device Selection Page
Note:
2. Registration process for the CyberClocks Online:
a. Go to CyberClocks Online website
b. Fill out the registration form. You need to have a valid e-mail address consists of a work-related e-mail.
c. Make sure to check the “non-standard devices” box in the registration form
d. Enter your cypress contact person.
e. The approval process can take up to 48 hours.
f. Upon the approval, the user will receive an e-mail indicating that the request has been successfully processed.
3. For more detailed information on all the functions of the software and programmer, please see the user manual.
Document #: 38-07409 Rev. *F
Page 3 of 6
CY3672
Step 7
Step 9
Step 11
Figure 5. CY3672 Software, Programming Sequence
Document #: 38-07409 Rev. *F
Page 4 of 6
CY3672
Sockets
To order additional sockets for the other devices listed below,
please contact your local Cypress FAE or go to
http://www.onfulfillment.com/cypressstore and click on
“Timing Technology.”
Table 1
below lists the available sockets
and their corresponding devices and configuration software.
Table 1. Available Sockets
Socket Part Number
CY3695
CY3696
CY3697
CY3698
CY3699
CY3690
CY3691
CY3692
CY3693
CY3694
CY3613
CY3724
CY3617
CY3618
Socket Label
CY3672ADP000
CY3672ADP001
CY3672ADP002
CY3672ADP003
CY3672ADP004
CY3672ADP008
CY3672ADP009
CY3672ADP006
CY3672ADP007
CY3672ADP005
CY3672ADP013
CY3672ADP021
CY3672ADP016
CY3672ADP017
CY25200F
CY2077FS
CY2077FZ
CY22381F
CY25100ZCF
CY25100SCF
CY23FP12
CY26049
CY27EE16
CY25701FJXC
CY25701FLXC
CY25702FJXC
CY25702FXCT
Programming Device
CY22050F, CY22150F
Configuration Software
CyberClocks
CyberClocks Online
CyberClocks
CyberClocks
CyberClocks
CyberClocks Online
CyberClocks Online
CyberClocks
CyberClocks
CyberClocks
CyberClocks Online
CyberClocks Online
CyberClocks Online
CyberClocks Online
CY22392F, CY22393F, CY22394F, CY22395F CyberClocks
Ordering Information
Ordering Code
CY3672
CY3672-PRG
CY3672-USB
CY3690
CY3691
CY3692
CY3693
CY3694
CY3695
CY3696
CY3697
CY3698
CY3699
CY3613
CY3724
CY3617
CY3618
FTG Programmer
FTG Programmer with USB Support
CY25100ZCF Socket Adapter (TSSOP)
CY25100SCF Socket Adapter (SOIC)
CY23FP12
CY26049
CY27EE16
CY22050F, CY22150F, CY25200F
CY2077FS
CY2077FZ
CY22392F, CY22393F, CY22394F, CY22395F
CY22381F
CY25701FJXC
CY25701FLXC
CY25702FJXC
CY25702FXCT
Package description
FTG Development Kit
Operating Voltage
110V/220V
110V/220V
110V/220V
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Microsoft and Windows are registered trademarks of Microsoft Corporation. CyberClocks and CyClocksRT are trademarks of
Cypress Semiconductor Corporation. All product and company names mentioned in this document are the trademarks of their
respective holders.
Document #: 38-07409 Rev. *F
Page 5 of 6
© Cypress Semiconductor Corporation, 2005. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Talking
京公网安备 11010802033920号
EEWORLD
