EEWORLDEEWORLDEEWORLD

Part Number

Search

296HG222B3C

Description
Potentiometer, Carbon Composition, 0.15W, 2200ohm, 350V, 20% +/-Tol, 4925,
CategoryPassive components    The resistor   
File Size366KB,2 Pages
ManufacturerCTS
Environmental Compliance
Download Datasheet Parametric View All

296HG222B3C Overview

Potentiometer, Carbon Composition, 0.15W, 2200ohm, 350V, 20% +/-Tol, 4925,

296HG222B3C Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid224689211
Reach Compliance Codeunknown
Electrocomponents
®
Series 296
Data Sheet
Rotary Potentiometer
Commercial
12mm Diameter
Carbon Composition
Rotary Potentiometer
Features
• Miniature 12mm size
• Low cost
• Snap-in bracket for PC board mounting
• Detent available
• Insulated shaft available
• RoHS compliant
Electrical and Mechanical Specifications
Resistance Range
500 ohms through 1 Megohms
Resistance Tolerance
±30%, ±20%, ±10%
Power Rating
0.15 watts @ 50°C
Dielectric Strength
500 VDC for 1 minute
Maximum Operating Voltage
350 VDC
Insulation Resistance
100 Megohms minimum @ 250 VDC
Rotational Angle
Mechanical angle: 300°
Effective angle: 280°
Rotational Torque
20 – 216 gf-cm
Stop Strength
5.76 kg-cm minimum (VR without detent)
3 kg-cm minimum (VR with detent)
Mounting Information
P.C. board mounting
Type "X": Shaft parallel to P.C. board
Type "U": Shaft vertical to P.C. board
Type "H": Same as "X" except hook terminals
Detent
Detent @ 50% rotation
Push-Pull strength on shaft
8 kg for 10 seconds
Rotational life
10K cycles
Operating temperature
-10°C ~ 80°C
Solder Heat Resistance
260°C for 5 seconds
1-2
CTS Electrocomponents
© 2009 CTS Corporation. All rights reserved. Information subject to change.
www.ctscorp.com
2/06/09
After adding shutdown and low power consumption, stm32 will run away after working for 8-9 hours
This is the first time I use stm32, the chip is STM32F103CBT7. The working process is: at fixed intervals, an external interrupt will wake up the CPU for measurement, store the data in the on-chip fla...
xiaowanzi111 stm32/stm8
[Silicon Labs Development Kit Review] +6-axis inertial sensor ICM-20648
ICU-20648 is a 6- input inertial sensor, a 3 -axis gyroscope, a 3- axis accelerometer and a Digital Motion Processor (DMP) in a 24- pin QFN package . It has an on-chip 16 -bit ADC and a communication ...
anger0925 Development Kits Review Area
Welcome our new moderator, Azuma Simeng~~
Good afternoon, everyone~~I am very happy to tell you that our moderator team has expanded again.Welcome moderator Wu Zushi Meng to take office~~~ Let us work together to maintain and operate the embe...
okhxyyo Embedded System
Thanks to all the staff of Electronic Engineering Forum
I am very grateful to the family of the Electronic Engineering Forum! When I was most ignorant and helpless, you helped me to provide posting services, so that more people could become our potential c...
张惠的 Talking
TI DSP--Memory space allocation and designation
In CCS programming, if we do not specify the storage location of variables/codes, the compiler will automatically assign a location to the variables/codes. However, if we need to put variables in a sp...
fish001 DSP and ARM Processors
Reward (1000RMB) 3-output Hall speed sensor chip selection and external circuit design
I want to make a Hall speed sensor to detect gear speed. I hope this sensor has 3 voltage digital signal outputs: 2 speed voltage digital signals and 1 rotation direction digital signal. I have contac...
genesis945 Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号