It is recommended that the temperature of the part does not exceed 125°C
under worst case operating conditions.
Ambient temperature: -40°C to +75°C (refering to IR)
Operating temperature: -40°C to +125°C
Storage temperature (on tape & reel): -20°C to +40°C; 75% RH max.
Test conditions of Electrical Properties: 20°C, 33% RH
if not specified differently
DESCRIPTION
3.0
2.0
REV
2012-09-03
2009-11-02
DATE
SSt
ME
BY
BD
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
www.we-online.com
eiSos@we-online.com
WE-HCI SMD Flat Wire High Current
Inductor
Order.- No.
SIZE
A4
74435571100
Size: 1890
CHECKED
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use.
Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before
the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
F Typical Inductance vs. Current Characteristics:
F Typical Temperature rise vs. Current Characteristics:
DESCRIPTION
3.0
2.0
REV
2012-09-03
2009-11-02
DATE
SSt
ME
BY
BD
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
www.we-online.com
eiSos@we-online.com
WE-HCI SMD Flat Wire High Current
Inductor
Order.- No.
SIZE
A4
74435571100
Size: 1890
CHECKED
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use.
Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before
the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
G Packaging Specification: [mm]
DESCRIPTION
3.0
2.0
REV
2012-09-03
2009-11-02
DATE
SSt
ME
BY
BD
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
www.we-online.com
eiSos@we-online.com
WE-HCI SMD Flat Wire High Current
Inductor
Order.- No.
SIZE
A4
74435571100
Size: 1890
CHECKED
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use.
Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before
the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
H Soldering Specifications:
H1: Classification Reflow Profile for SMT components:
H2: Classification Reflow Profiles
Profile Feature
Preheat
- Temperature Min (Tsmin)
- Temperature Max (Tsmax)
- Time (ts) from (Tsmin to Tsmax)
Ramp-up rate (TL to TP)
Liquidous temperature (TL)
Time (tL) maintained above TL
Peak package body temperature (Tp)
Time within 5°C of actual peak temperature (tp)
Ramp-down rate (TP to TL)
Time 25°C to peak temperature
refer to IPC/JEDEC J-STD-020D
Pb-Free Assembly
150°C
200°C
60-180 seconds
3°C/ second max.
217°C
60-150 seconds
See Table H3
20-30 seconds
6°C/ second max.
8 minutes max.
H3: Package Classification Reflow Temperature
Package Thickness
PB-Free Assembly
PB-Free Assembly
PB-Free Assembly
refer to IPC/JEDEC J-STD-020D
< 1.6 mm
1.6 - 2.5 mm
≥ 2.5 mm
Volume mm³
<350
260°C
260°C
250°C
Volume mm³
350 - 2000
260°C
250°C
245°C
Volume mm³
>2000
260°C
245°C
245°C
DESCRIPTION
3.0
2.0
REV
2012-09-03
2009-11-02
DATE
SSt
ME
BY
BD
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
www.we-online.com
eiSos@we-online.com
WE-HCI SMD Flat Wire High Current
Inductor
Order.- No.
SIZE
A4
74435571100
Size: 1890
CHECKED
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use.
Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before
the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
I Cautions and Warnings:
The following conditions apply to all goods within the product series of WE-HCI
of Würth Elektronik eiSos GmbH & Co. KG:
General:
All recommendations according to the general technical specifications of the data-sheet have to be complied with.
The disposal and operation of the product within ambient conditions which probably alloy or harm the wire isolation has to be avoided.
If the product is potted in customer applications, the potting material might shrink during and after hardening. Accordingly to this the product
is exposed to the pressure of the potting material with the effect that the core, wire and termination is possibly damaged by this pressure and
so the electrical as well as the mechanical characteristics are endanger to be affected. After the potting material is cured, the core, wire and
termination of the product have to be checked if any reduced electrical or mechanical functions or destructions have occurred.
The responsibility for the applicability of customer specific products and use in a particular customer design is always within the authority of
the customer. All technical specifications for standard products do also apply for customer specific products.
Cleaning agents that are used to clean application might damage or change the characteristics of the component, body, pins or termination.
Direct mechanical impact to the product shall be prevented as the core material could flake or in the worst case it could break.
Product specific:
Follow all instructions mentioned in the datasheet, especially:
•The solder profile has to be complied with according to the technical reflow soldering specification, otherwise no warranty will be sustai-
ned.
•All products are supposed to be used before the end of the period of 12 months based on the product date-code, if not a 100% solderabi-
lity can´t be warranted.
•Violation of the technical product specifications such as exceeding the nominal rated current will result in the loss of warranty.
•Due to heavy weight of the components of size 2212, strong forces and high accelerations might have the effect to damage the electrical
connection or to harm the circuit board and will result in the loss of warranty.
DESCRIPTION
3.0
2.0
REV
2012-09-03
2009-11-02
DATE
SSt
ME
BY
BD
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
www.we-online.com
eiSos@we-online.com
WE-HCI SMD Flat Wire High Current
Inductor
Order.- No.
SIZE
A4
74435571100
Size: 1890
CHECKED
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use.
Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before
the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
Harmonic current and voltage fluctuation and flicker are the last two of the four EMI projects. Next week we will start introducing EMS test methods. Welcome to follow the official account Monster Ele...
What is the relationship between transformers and inductors? Let me first state the conclusion: transformers and inductors are both related and unrelated, just like the internal resistance of a power ...
I have a new project recently, which requires a built-in 3.7V lithium battery. The battery type has not been selected yet, but I plan to choose between 18650 and lithium polymer batteries.Lithium poly...
[i=s]This post was last edited by Xiaoyangyy on 2021-9-6 11:02[/i]When choosing a MOS tube for a circuit, should I look at the power or Tj? I am confused.Let’s take the above circuit as an example. Th...
An oscilloscope is a very versatile electronic measuring instrument that can convert electrical signals invisible to the naked eye into visible images. An oscilloscope uses a narrow electron beam c...[Details]
The source program is mainly written with these basic instructions to achieve your control tasks. However, in order to increase the readability and maintainability of the source program, we introdu...[Details]
Honor held a new product launch conference online today, and the company's CEO also showed off their smart manufacturing factory, which was quite impressive. According to Zhao Ming's statement at t...[Details]
Assuming the system clock is 72Mhz, TIM1 is obtained from PCLK2 (72MHz), and TIM2-7 is obtained from PCLK1.
The key is to set the clock pre-division number and the value of the automatic reload regis...[Details]
On November 23, Sihui Fusi stated on the interactive platform that the company mainly provides central console mainboards, headlight boards and other products to Xiaopeng Motors. At the same time, Si...[Details]
The running light is a must-learn experiment for those who are new to microcontrollers. The main operations involved are shift operations and delay control. When you don't have access to a timer, you ...[Details]
Industrial wireless applications bring numerous new capabilities to the industries they serve, such as enabling new types of monitoring, increasing the flexibility of existing equipment, and reducing...[Details]
The electronics for automotive infotainment TFT-LCD displays must be minimal to limit PCB size and cost. After reviewing the drawbacks of typical low-integration solutions, we introduce a new appro...[Details]
I recently wanted to write a program using an STC microcontroller, but STC was not in the KEIL microcontroller library, so I just found a replacement. However, the Keil I found did not add the StartUp...[Details]
principle When setting the contrast of the 1602 screen, we can see a 5*8 dot matrix. In fact, the LCD displays the character fonts (picture below), and the CGROM has been defined and can only be r...[Details]
In 2019, Amazon, Apple, Google and Zigbee Alliance members jointly formed the Home Connected Internet Protocol Project (CHIP). The working group developed a new standard that enables IP-based commun...[Details]
On August 21, Desay SV released an investor relations activity record, responding to investors' questions about its first-half operating results, R&D investment, autonomous driving products, etc. In ...[Details]
/************************************************************************
Function: Read_74HC595
Description: Read the input data of n 74HC595s
Calls: HC595_delay; GPIO_ResetBits; GPIO_SetBit...[Details]
According to Video Hall, BOE plans to add 4K 240Hz panels in the third quarter of 2022, with higher specifications than the current 4K 144Hz/165Hz. According to reports, BOE plans to launc...[Details]
1 Introduction to MSP430 power saving mode
MSP430 is famous for its low power consumption. It can connect two external clock sources - XIN and XT2IN. There is also an internal DC0 oscillator, which...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
