EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

KH210-810B27K

Description
Fixed Resistor, Wire Wound, 7W, 27000ohm, 10% +/-Tol, -10,10ppm/Cel,
CategoryPassive components    The resistor   
File Size626KB,4 Pages
ManufacturerVitrohm Portuguesa LDA
Environmental Compliance
Download Datasheet Parametric View All

KH210-810B27K Overview

Fixed Resistor, Wire Wound, 7W, 27000ohm, 10% +/-Tol, -10,10ppm/Cel,

KH210-810B27K Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid938961051
Reach Compliance Codecompliant
Country Of OriginPortugal
ECCN codeEAR99
YTEOL7.1
structureCeramic Case
Lead diameter0.8 mm
Lead length36 mm
Installation featuresTHROUGH HOLE MOUNT
Number of terminals2
Maximum operating temperature350 °C
Minimum operating temperature-55 °C
Package height6.4 mm
Package length38 mm
Package shapeRECTANGULAR PACKAGE
Package formAxial
Package width6.4 mm
method of packingBULK
Rated power dissipation(P)7 W
Rated temperature70 °C
resistance27000 Ω
Resistor typeFIXED RESISTOR
surface mountNO
technologyWIRE WOUND
Temperature Coefficient10 ppm/°C
Terminal shapeWIRE
Tolerance10%
Operating Voltage434.74 V
Signal Processing of Linear Frequency Modulated Stepped Synthetic Aperture Radar System
Abstract: To improve the range resolution, the bandwidth of the transmitted signal is usually increased, which leads to a high sampling rate and A/D conversion rate of the system, a sharp increase in ...
JasonYoo DSP and ARM Processors
AC-DC adapter reference design with TI's latest UCC28780 chip and Type-C interface
TI's UCC28780 is a high-frequency active clamp flyback controller with fully and partially zero-voltage switching (ZVS) primary FETs with adaptive control, programmable timing for external Si or GaN F...
alan000345 Analogue and Mixed Signal
An article explains the function and principle of Via hole
As shown in the figure, what is the role and principle of adding a ground via hole near the via hole of the routing? The vias of the PCB board can be classified into the following types according to t...
随和的雏菊 PCB Design
PWM principle and code implementation of STM32 breathing light
Generating PWM Waves Using Timers PWM stands for Pulse Width Modulation. By controlling the duty cycle of high-frequency signals, the eye acts as a low-pass filter to control brightness. By changing t...
可乐zzZ stm32/stm8
NUCLEO's ST-LINK is changed to 1.8V and the computer cannot recognize the hardware
I want to debug the LIS25BA sensor. I don't have a level conversion chip, so I want to change the NUCLEO to 1.8V power supply. For debugging convenience, I first changed the 3.3V LDO of ST-LINK to 1.8...
littleshrimp stm32/stm8
What programming method should be used for the M9S8AC16CG chip?
I am a novice and recently I have been using the M9S8AC16CG chip. Could you please tell me what software I should use for programming?...
lxz1791819545 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号