Above ratings are based on the thermal resistances using a multi-layer circuit board (EIA/JESD51). For mounting on a mono-layer board, power derating shall be
needed. Please inquire of us about conditions.
※1 素子毎の負荷電力の合計が、パッケージ定格電力を超えない条件で御½用ください。
※1 Total power consumption of all elements should not exceed the package power rating.
The resistor of this product is formed by narrow patterning a thin metal film. Thus, application of excessive voltage causes burn and destruction of the resistive film, abnormality
in resistance or open resistance and loss of proper function. The properly and electrostatically measured taping materials are used for the components, but attention should be paid
to the fact that there is some danger the parts may be destructed by static electricity(equivalent to 500V or over at 100pF, 1.5kΩ) to cause a change in resistance in the conditions
of an excessive dryness when mounting on the boards. Similarly, care should be given not to apply the excessive static electricity at the time of mounting on the boards. When
designing, consideration can be taken into withstanding ESD for customized KPC products. Please consult with us about the details.
●
Hand soldering by iron soldering or repairment are not recommended because KPC is a multi-pin product.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. In the case of 5〜35℃/35〜75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas
like hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
Since I am in the industrial control industry, I basically work on RS485 interfaces and network ports. When I designed the schematic, I expanded the 485 interface, 2 CAN interfaces, 1 Ethernet interfa...
Sitara ARM Microprocessors– The Sitara product platform includes high-performance ARM Cortex-A8 and ARM9-based embedded microprocessors ranging from 375MHz to 1.GHz, with future roadmap devices exceed...
[i=s] This post was last edited by lb8820265 on 2018-12-11 21:52[/i] [align=left][font=微软雅黑] This time I will introduce the selection of BLE and MEMS. It is often said that choice is more important th...
Source: csdnRecently, an Oracle employee revealed on a social platform that they are currently laying off employees with N+6 compensation.In fact, Oracle has been laying off employees in Beijing since...
In addition, when using GPIO, you also need to consider the pin reuse of the corresponding chip. Taking 6455 as an example, the GPIO pin reuse is as shown in the figure below:It can be seen that most ...
By the way, silicone pads can be purchased according to the device package, and the appearance and screw holes are ready.
When we bought a whole roll of silicone pads, there was no problem in cutting ...
When I was reading the chip manual of SDRAM, I kept thinking about this question: How is the capacity of SDRAM calculated? After searching various materials on the Internet, I finally share my summar...[Details]
1. Another external interrupt The previous two lectures were about external interrupt 0 (the function of P3.2). Here we also have an external interrupt 1 (the function of P3.3). To achieve the funct...[Details]
How to build a scalable SCR-based burglar alarm
This is a simple
burglar alarm
circuit
thyristor
. Its features include automatic entry and exit delay - bell along with ti...[Details]
In fact, STM8 does not need a crystal oscillator and reset circuit, but in order to ensure the stable operation of the minimum system, it is best to add an external circuit.
● STM8 reset circui...[Details]
According to Reuters, Chinese electric vehicle (EV) leader BYD has reached an agreement with Huawei to introduce Huawei's advanced autonomous driving system in its off-road el...[Details]
LED
has the characteristics of low energy consumption, long life, low heat generation and environmental protection, and has been widely used in many fields, such as:
1 Lighting field Str...[Details]
With the advent of HSDPA, data can be transmitted at a faster speed than traditional WCDMA. This is mainly achieved through a more complex modulation format and repeated steps of sending data. Thes...[Details]
Panasonic is seeking to buy land in the United States to build a large factory to produce batteries for Tesla's new electric vehicles, according to Japan's NHK. NHK reported that Panasonic is cons...[Details]
According to iMedia Research, the scale of China's AIoT hardware market will exceed one trillion by 2020. The real-time and effective processing of the massive data generated by IoT devices will be t...[Details]
All of us around the world are dealing with this challenging new environment. I’m lucky enough to only have to share my home office with a teacher! In the face of the reality, companies are finding...[Details]
To be honest, it's my junior year summer vacation and I'm still working on 51 single-chip microcomputers. The key is that I encountered a problem that took me a whole day to solve. It's really embarr...[Details]
introduction A switching power supply is a power supply that uses modern power electronics technology to control the time ratio of the switching transistor to turn on and off to maintain a stable...[Details]
This afternoon, ZTE held a launch conference for the Axon 40 series, in which the Axon 40 Ultra returned to a minimalist design and was equipped with a Snapdragon 8 Gen 1 chip. In terms of appeara...[Details]
On October 16, the second Midea Visionary Conference was held in Shunde, Foshan. Academician of the Chinese Academy of Sciences and professor of Huazhong University of Science and Technology Ding Han,...[Details]
GD32 MCU
京公网安备 11010802033920号
EEWORLD
