0041.9148.5.2.1.3 datasheet, PDF

0041.9148.5.2.1.3: DescriptionPushbutton Switch, SPST, On-(off), Momentary, 0.2A, 50VDC, 6 PCB Hole Cnt, Solder Terminal, Through Hole-straight; CategoryMechanical and electronic products switch; File Size195KB，12 Pages; ManufacturerSCHURTER; Websitehttp://www.schurterinc.com/; Environmental Compliance

Download Datasheet Parametric View All

0041.9148.5.2.1.3 Overview

Pushbutton Switch, SPST, On-(off), Momentary, 0.2A, 50VDC, 6 PCB Hole Cnt, Solder Terminal, Through Hole-straight

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Reach Compliance Code	compliant
ECCN code	EAR99
Is Samacsys	N
Actuator angle
Actuator color	GREEN
Actuator length	0.299 inch
Actuator material	POLYCARBONATE
Actuator type	PUSHBUTTON
Other features	SQR RED BEZEL,RND BUTN,RED LED
body width
body height	12.0904 mm
Body length or diameter
Casing diameter
Nozzle length
center contact material	BRASS
Center contact plating	SILVER
Contact (AC) maximum rated R load	0.2A@60VAC
Maximum contact current (AC)	0.2 A
Maximum contact current (DC)	0.2 A
Contact (DC) maximum rated R load	0.2A@50VDC
Contact function	ON-(OFF)
Contact resistance	0.025 mΩ
Maximum contact voltage (AC)	60 V
Maximum contact voltage (DC)	50 V
Electrical life	100000 Cycle(s)
End contact material	BRASS
End contact plating	SILVER
illumination	LED
Insulation resistance	10000000000 Ω
insulator material	POLYSULFONE
JESD-609 code	e3
Manufacturer's serial number	LDT
Installation features	THROUGH HOLE-STRAIGHT
Maximum operating temperature	60 °C
Minimum operating temperature	-25 °C
PCB hole count	6
surface mount	NO
Switch action	MOMENTARY
switch function	SPST
Switch type	PUSHBUTTON SWITCH
Terminal surface	Matte Tin (Sn)
Terminal length	0.134 inch
Terminal material	BRASS
Termination type	SOLDER
Base Number Matches	1

[Popular Science] What are the pulse signal parameters? How can we get the desired pulse signal parameters?: [Popular Science] What are the pulse signal parameters? How can we get the desired pulse signal parameters?...; aigtekatdz Test/Measurement

LED Driver: When driving LED, there should be two situations, such as using common anode connection and common cathode connection. When using common anode, the positive end of LED is connected to the positive pow...; soso Analog electronics

Selection of HAL library and STD library: Compared to the STD library, some statements seem to have become longer. If you write code in KEIL, it feels really painful. Of course, it has no effect on me. I write code in vscode, which has an ama...; vincent.liu stm32/stm8

Reasonable avoidance: Supporting seamless communication and non-interference vehicle-to-everything design: Did you know that there are more electronics and radios in today’s cars than in the first space capsule sent to the moon? To benefit from all the technology, all of these communication radios must wor...; 石榴姐 RF/Wirelessly

Configuration example - ModbusTCP to Profinet gateway to connect tightening shaft drive: Prepare a Siemens 1200 PLC, a Modbus TCP to Profinet gateway and a tightening shaft driver.The article content is a configuration example of connecting the Modbus TCP to Profinet gateway to the driver...; bjnytx Test/Measurement

Renesas CPK-RA6M4 Development Board Review----I2C: Hardware introduction of functional modules--I2CI2C (Inter Integrated Circuit) bus is a half-duplex, bidirectional two-wire synchronous serial bus developed by PHILIPS. I2C bus only needs two signal l...; chen@peng Renesas Electronics MCUs

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components