D/CRCW-P
www.vishay.com
Vishay
Lead (Pb)-Bearing Thick Film, Rectangular,
Semi-Precision Chip Resistors
FEATURES
• Low temperature coefficient (50 ppm/K) and tight
tolerances (± 0.25 %)
• Lead (Pb)-bearing termination plating on Ni barrier layer
• Metal glaze on high quality ceramic
• Material categorization: For definitions of compliance
please see
www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
CASE
SIZE
INCH
CASE
SIZE
METRIC
POWER
RATING
P
70
W
LIMITING
ELEMENT
VOLTAGE
U
max.
AC
RMS
/DC
V
50
TEMPERATURE
COEFFICIENT
ppm/K
RESISTANCE
RANGE
MODEL
TOLERANCE
%
SERIES
D10/CRCW0402-P
0402
1005
0.063
± 100
± 50
± 100
± 0.5
± 0.25, ± 0.5, ± 1
± 0.5
± 0.25
± 0.5, ± 1
± 0.5
± 0.25
± 0.5, ± 1
± 0.5
± 0.25
± 0.5, ± 1
± 0.5
± 0.5, ± 1
± 0.5
± 0.5, ± 1
± 0.5
± 0.5, ± 1
± 0.5
± 0.5, ± 1
10 to 1M
100 to 1M
10 to 10M
100 to 1M
100 to 10M
10 to 10M
100 to 1M
100 to 10M
10 to 10M
100 to 1M
100 to 10M
100 to 1M
100 to 1M
100 to 2.2M
100 to 2.2M
10 to 10M
100 to 10M
10 to 10M
100 to 10M
E24; E96
D11/CRCW0603-P
0603
1608
0.1
75
± 50
± 100
E24; E96
D12/CRCW0805-P
0805
2012
0.125
150
± 50
± 100
E24; E96
D25/CRCW1206-P
1206
3216
0.25
200
± 50
± 100
± 50
± 100
± 50
± 100
± 50
± 100
± 50
E24; E96
CRCW1210-P
CRCW1218-P
CRCW2010-P
CRCW2512-P
1210
1218
2010
2512
3225
3246
5025
6332
0.5
1.0
0.75
1.0
200
200
400
500
E24; E96
E24; E96
E24; E96
E24; E96
Notes
• These resistors do not feature a limited lifetime when operated within the limits of rated dissipation, permissible operating voltage and
permissible film temperature. However, the resistance typically increase due to the resistor’s film temperature over operating time generally
known as drift. The drift may exceed the stability requirements of an individual application circuit and thereby limits the functional time.
• Marking and packaging: See datasheet “Surface Mount Resistor Marking” (www.vishay.com/doc?20020).
• Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material.
Revision: 21-Jan-14
Document Number: 20009
1
For technical questions, contact:
thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
D/CRCW-P
www.vishay.com
Vishay
TECHNICAL SPECIFICATIONS
PARAMETER
Rated Dissipation at
P
70 (1)
Operating Voltage
U
max.
AC
RMS
/DC
Insulation Voltage
U
ins
(1 min)
Insulation Resistance
Operating Temperature Range
Failure Rate
Weight
UNIT
W
V
V
°C
h
-1
mg
0.65
2
5.5
10
D10/
D11/
D12/
D25/
CRCW1210-P CRCW1218-P CRCW2010-P CRCW2512-P
CRCW0402-P CRCW0603-P CRCW0805-P CRCW1206-P
0.063
50
75
0.1
75
100
0.125
150
200
0.25
200
300
> 10
9
- 55 to + 155
0.3 x 10
-9
16
29.5
25.5
40.5
0.33
200
300
1
200
300
0.5
400
300
1
500
300
Note
(1)
The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.
PART NUMBER AND PRODUCT DESCRIPTION
PART NUMBER: CRCW080525R0DKTAP
C
R
C
W
0
8
0
5
2
5
R
0
D
K
T
A
P
MODEL
CRCW0402
CRCW0603
CRCW0805
CRCW1206
CRCW1210
CRCW1218
CRCW2010
CRCW2512
RESISTANCE
R
= Decimal
K
= Thousand
M
= Million
TOLERANCE
C
= ± 0.25 %
D
= ± 0.5 %
F
= ± 1.0 %
TCR
H
= ± 50 ppm/K
K
= ± 100 ppm/K
PACKAGING
TA, TB,
TC, TD,
TE, TF,
TG, TH,
TK
SPECIAL
Up to 2 digits
P
=
Semi-Precision
PRODUCT DESCRIPTION: CRCW0805-P 100 25R 0.5% RT1
CRCW0805-P
MODEL
CRCW0402-P
CRCW0603-P
CRCW0805-P
CRCW1206-P
CRCW1210-P
CRCW1218-P
CRCW2010-P
CRCW2512-P
100
TCR
± 50
ppm/K
± 100
ppm/K
75R
RESISTANCE
49K9
= 49.9 k
5R1
= 5.1
0.5 %
TOLERANCE
± 0.25 %
± 0.5 %
±1%
RT1
PACKAGING
RT1, RT5,
RT6, RT7
RT4, R02,
R67, R82,
RT9
Revision: 21-Jan-14
Document Number: 20009
2
For technical questions, contact:
thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
D/CRCW-P
www.vishay.com
Vishay
QUANTITY
10 000
50 000
5000
10 000
20 000
5000
10 000
20 000
5000
10 000
20 000
5000
10 000
20 000
4000
4000
2000
4000
Blister tape acc. to
IEC 60068-3
Type II
12 mm
12 mm
12 mm
4 mm
4 mm
8 mm
4 mm
12 mm
4 mm
8 mm
4 mm
Paper tape acc. to
IEC 60068-3
Type I
8 mm
4 mm
8 mm
4 mm
CARRIER TAPE
WIDTH
8 mm
PITCH
2 mm
REEL DIAMETER
180 mm/7"
330 mm/13"
180 mm/7"
285 mm/11.25"
330 mm/13"
180 mm/7"
285 mm/11.25"
330 mm/13"
180 mm/7"
285 mm/11.25"
330 mm/13"
180 mm/7"
285 mm/11.25"
330 mm/13"
180 mm/7"
180 mm/7"
180 mm/7"
PACKAGING
MODEL
D10/CRCW0402-P
CODE
TD = RT7
TE = RF4
TA = RT1
D11/CRCW0603-P
TB = RT5
TC = RT6
TA = RT1
D12/CRCW0805-P
TB = RT5
TC = RT6
TA = RT1
D25/CRCW1206-P
TB = RT5
TC = RT6
TA = RT1
CRCW1210-P
CRCW1218-P
CRCW2010-P
CRCW2512-P
TB = RT5
TC = RT6
TK = RT9
TF = R02
TG = R67
TH = R82
DIMENSIONS
in millimeters
SIZE
INCH METRIC
0402
0603
0805
1206
1210
1218
2010
2512
1005
1608
2012
3216
3225
3246
5025
6332
L
1.0 ± 0.05
1.55
2.0
3.2
+ 0.10
- 0.05
+ 0.20
- 0.10
+ 0.10
- 0.20
DIMENSIONS
W
0.5 ± 0.05
0.85 ± 0.1
H
T1
T2
0.2 ± 0.1
0.3 ± 0.2
0.3 ± 0.2
0.4 ± 0.2
0.4 ± 0.2
0.4 ± 0.2
0.6 ± 0.2
0.6 ± 0.2
SOLDER PAD DIMENSIONS
REFLOW SOLDERING
a
0.4
0.5
0.7
0.9
0.9
1.05
1.0
1.0
b
0.6
0.9
1.3
1.7
2.5
4.9
2.5
3.2
l
0.5
1.0
1.2
2.0
2.0
1.9
3.9
5.2
0.9
0.9
1.1
1.1
1.25
1.2
1.2
0.9
1.3
1.7
2.5
4.8
2.5
3.2
1.0
1.3
2.3
2.2
1.9
3.9
5.2
WAVE SOLDERING
a
b
l
0.35 ± 0.05 0.25 ± 0.05
0.45 ± 0.05
0.3 ± 0.2
0.3
+ 0.20
- 0.10
1.25 ± 0.15 0.45 ± 0.05
1.6 ± 0.15
2.5 ± 0.2
4.6 ± 0.15
2.5 ± 0.15
3.15 ± 0.15
0.55 ± 0.05
0.55 ± 0.05
0.55 ± 0.05
0.6 ± 0.1
0.6 ± 0.1
0.45 ± 0.2
0.45 ± 0.2
0.45 ± 0.2
0.6 ± 0.2
0.6 ± 0.2
3.2 ± 0.2
3.2
+ 0.10
- 0.20
5.0 ± 0.15
6.3 ± 0.2
Revision: 21-Jan-14
Document Number: 20009
3
For technical questions, contact:
thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
D/CRCW-P
www.vishay.com
FUNCTIONAL PERFORMANCE
Fraction of Rated Dissipation
P
70
Vishay
100
%
50
0
- 50
0
50
100
°C
150
70
Ambient Temperature in
amb
TEST PROCEDURES AND REQUIREMENTS
IEC
EN 60115-1 60068-2
CLAUSE
TEST
METHOD
TEST
PROCEDURE
REQUIREMENTS
PERMISSIBLE CHANGE (R)
STABILITY CLASS 1 OR BETTER
1 to 10 M
± 0.25 %; ± 0.5 %; ± 1 %
No flashover or breakdown
± (0.25 %
R
+ 0.05
)
Stability for product types:
D/CRCW-P
4.5
4.7
4.13
-
-
-
Resistance
Voltage proof
Short time overload
-
U
= 1.4 x
U
ins
; 60 s
U
= 2.5 x
P
70
x
R
2 x
U
max.;
duration acc. to style
Solder bath method;
Sn60Pb40
non-activated flux;
(235 ± 5) °C
(2 ± 0.2) s
4.17.2
58 (Td)
Solderability
Solder bath method;
Sn96.5Ag3Cu0.5
non-activated flux;
(245 ± 5) °C
(3 ± 0.3) s
4.8.4.2
4.32
4.33
-
21 (Uu
3
)
21 (Uu
1
)
Temperature
coefficient
Shear
(adhesion)
Substrate bending
(20/- 55/20) °C and
(20/125/20) °C
RR 1608 and smaller: 9 N
RR 2012 and larger: 45 N
Depth 2 mm;
3 times
30 min at - 55 °C;
30 min at 125 °C
5 cycles
1000 cycles
Good tinning ( 95 % covered)
no visible damage
Good tinning ( 95 % covered)
no visible damage
± 50 ppm/K; ± 100 ppm/K
No visible damage
No visible damage, no open circuit in bent position
± (0.25 %
R
+ 0.05
)
4.19
14 (Na)
Rapid change of
temperature
± (0.25 %
R
+ 0.05
)
± (1 %
R
+ 0.05
)
Revision: 21-Jan-14
Document Number: 20009
4
For technical questions, contact:
thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
D/CRCW-P
www.vishay.com
Vishay
TEST PROCEDURES AND REQUIREMENTS
IEC
EN 60115-1 60068-2
CLAUSE
TEST
METHOD
TEST
PROCEDURE
REQUIREMENTS
PERMISSIBLE CHANGE (R)
STABILITY CLASS 1 OR BETTER
1 to 10 M
Stability for product types:
D/CRCW-P
4.23
4.23.2
4.23.3
4.23.4
4.23.5
4.23.6
4.23.7
-
2 (Ba)
30 (Db)
1 (Aa)
13 (M)
30 (Db)
-
Climatic sequence:
Dry heat
Damp heat, cyclic
Cold
Low air pressure
Damp heat, cyclic
DC load
-
125 °C; 16 h
55 °C;
90 % RH;
24 h; 1 cycle
- 55 °C; 2 h
1 kPa; (25 ± 10) °C; 1 h
55 °C;
90 % RH;
24 h; 5 cycles
U
=
P
70
x
R
U
=
P
70
x
R
U
max.;
1.5 h on; 0.5 h off;
4.25.1
-
Endurance at 70 °C
70 °C; 1000 h
70 °C; 8000 h
4.18.2
58 (Td)
Resistance to
soldering heat
Flamability,
needle flame test
Damp heat,
steady state
Endurance at
upper category
temperature
Electrostatic
discharge
(human body model)
Component solvent
resistance
Solvent resistance
of marking
Vibration, endurance
by sweeping
Solder bath method
(260 ± 5) °C;
(10 ± 1) s
IEC 60695-11-5;
10 s
(40 ± 2) °C;
(93 ± 3) % RH;
56 days
155 °C, 1000 h
IEC 61340-3-1;
3 pos. + 3 neg. discharges;
ESD voltage acc. to size
Isopropyl alcohol;
50 °C; method 2
Isopropyl alcohol;
50 °C; method 1,
toothbrush
f = 10 Hz to 2000 Hz;
x, y, z
1.5 mm;
A
200 m/s
2
;
10 sweeps per axis
U
=
4.37
-
Periodic electric
overload
Single pulse high
voltage overload,
10 μs/700 μs
15 x
P
70
x
R
2 x
U
max.;
0.1 s on; 2.5 s off;
1000 cycles
± (1 %
R
+ 0.05
)
± (1 %
R
+ 0.05
)
± (2 %
R
+ 0.05
)
± (0.25 %
R
+ 0.05
)
4.35
-
No burning after 30 s
± (1 %
R
+ 0.05
)
4.24
78 (Cab)
4.25.3
-
± (1 %
R
+ 0.05
)
4.40
4.29
4.30
-
45 (XA)
45 (XA)
± (1 %
R
+ 0.05
)
No visible damage
Marking legible,
no visible damage
4.22
6 (Fc)
± (0.25 %
R
+ 0.05
)
± (1 %
R
+ 0.05
)
4.27
-
Û
= 10 x
P
70
x
R
2 x
U
max.;
10 pulses
± (1 %
R
+ 0.05
)
All tests are carried out in accordance with the following specifications:
• EN 60115-1, generic specification
• EN 140400, sectional specification
• EN 140401-802, detail specification
• IEC 60068-2-x, variety of environmental test procedures
Packaging of components is done in paper or blister tapes according to IEC 60286-3.
Revision: 21-Jan-14
Document Number: 20009
5
For technical questions, contact:
thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
京公网安备 11010802033920号
EEWORLD
