100% pin-to-pin drop-in replacement to quartz-based XO
Excellent total frequency stability as low as ±20 ppm
Operating temperature from -40°C to 85°C. For 125°C and/or
-55°C options, refer to
SiT8919
and
SiT8921
Low power consumption of 4.9 mA typical at 1.8V
Standby mode for longer battery life
Fast startup time of 5 ms
LVCMOS/HCMOS compatible output
Industry-standard packages: 2.0 x 1.6, 2.5 x 2.0, 3.2 x 2.5,
5.0 x 3.2, 7.0 x 5.0 mm x mm
Instant samples with
Time Machine II
and
field programmable
oscillators
RoHS and REACH compliant, Pb-free, Halogen-free and
Antimony-free
For AEC-Q100 oscillators, refer to
SiT8924
and
SiT8925
◼
Ideal for GPON/EPON, network switches, routers.
servers, embedded systems
Ideal for Ethernet, PCI-E, DDR, etc.
Electrical Characteristics
All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise
stated. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics
Parameters
Output Frequency Range
Frequency Stability
Symbol
f
F_stab
Min.
115
-20
-25
-50
Operating Temperature Range
T_use
-20
-40
Supply Voltage
Vdd
1.62
2.25
2.52
2.7
2.97
2.25
Current Consumption
Idd
–
–
–
OE Disable Current
Standby Current
I_OD
I_std
–
–
–
–
–
Duty Cycle
Rise/Fall Time
DC
Tr, Tf
45
–
–
–
Output High Voltage
Output Low Voltage
VOH
VOL
90%
–
Typ.
–
–
–
–
–
–
1.8
2.5
2.8
3.0
3.3
–
6.2
5.5
4.9
–
–
2.6
1.4
0.6
–
1
1.3
0.8
–
–
Max.
137
+20
+25
+50
+70
+85
1.98
2.75
3.08
3.3
3.63
3.63
7.5
6.4
5.6
4.2
4.0
4.3
2.5
1.3
55
2
2.5
2
–
10%
Unit
MHz
ppm
ppm
ppm
°C
°C
V
V
V
V
V
V
mA
mA
mA
mA
mA
A
A
A
%
ns
ns
ns
Vdd
Vdd
No load condition, f = 125 MHz, Vdd = 2.8 V, 3.0 V, 3.3 V or
2.25 to 3.63 V
No load condition, f = 125 MHz, Vdd = 2.5 V
No load condition, f = 125 MHz, Vdd = 1.8 V
Vdd = 2.5 V to 3.3 V, OE = GND, Output in high-Z state
Vdd = 1.8 V, OE = GND, Output in high-Z state
ST = GND, Vdd = 2.8 V to 3.3 V, Output is weakly pulled down
ST = GND, Vdd = 2.5 V, Output is weakly pulled down
ST = GND, Vdd = 1.8 V, Output is weakly pulled down
All Vdds
Vdd = 2.5 V, 2.8 V, 3.0 V or 3.3 V, 20% - 80%
Vdd =1.8 V, 20% - 80%
Vdd = 2.25 V - 3.63 V, 20% - 80%
IOH = -4 mA (Vdd = 3.0 V or 3.3 V)
IOL = 4 mA (Vdd = 3.0 V or 3.3 V)
Inclusive of Initial tolerance at 25°C, 1
st
year aging at 25°C,
and variations over operating temperature, rated power
supply voltage and load.
Condition
Frequency Range
Frequency Stability and Aging
Operating Temperature Range
Extended Commercial
Industrial
Contact SiTime
for 1.5 V support
Supply Voltage and Current Consumption
LVCMOS Output Characteristics
Rev 1.06
15 March 2021
www.sitime.com
SiT8009B
High Frequency, Low Power Oscillator
Table 1. Electrical Characteristics (continued)
Parameters
Symbol
Min.
Typ.
–
–
87
Max.
–
30%
150
Unit
Condition
Input Characteristics
Input High Voltage
Input Low Voltage
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
50
2
Startup Time
Enable/Disable Time
Resume Time
RMS Period Jitter
T_start
T_oe
T_resume
T_jitt
–
–
–
–
–
Peak-to-peak Period Jitter
T_pk
–
–
RMS Phase Jitter (random)
T_phj
–
–
Vdd
Vdd
k
Pin 1, OE or ST
Pin 1, OE or ST
Pin 1, OE logic high or logic low, or ST logic high
–
–
Pin 1, ST logic low
M
Startup and Resume Timing
–
–
–
5
122
5
Jitter
1.9
1.8
12
14
0.5
1.3
3
4
25
30
0.9
2
ps
ps
ps
ps
ps
ps
f = 125 MHz, Vdd = 2.5 V, 2.8 V, 3.0 V or 3.3 V
f = 125 MHz, Vdd = 1.8 V
f = 125 MHz, Vdd = 2.5 V, 2.8 V, 3.0 V or 3.3 V
f = 125 MHz, Vdd = 1.8 V
Integration bandwidth = 900 kHz to 7.5 MHz
Integration bandwidth = 12 kHz to 20 MHz
ms
ns
ms
Measured from the time Vdd reaches its rated minimum value
f = 137 MHz. For other frequencies, T_oe = 100 ns + 3 * cycles
Measured from the time ST pin crosses 50% threshold
Table 2. Pin Description
Pin
Symbol
Output Enable
OE/ST /NC
̅ ̅̅
Functionality
H
[1]
: specified frequency output
L: output is high impedance. Only output driver is disabled.
H
[1]
: specified frequency output
L: output is low (weak pull down). Device goes to sleep mode. Supply
current reduces to I_std.
Any voltage between 0 and Vdd or Open
[1]
: Specified frequency
output. Pin 1 has no function.
Electrical ground
Oscillator output
Power supply voltage
[2]
OE/ST /NC
̅ ̅̅
1
Top View
4
VDD
1
Standby
No Connect
2
3
4
GND
OUT
VDD
Power
Output
Power
GND
2
3
OUT
Figure 1. Pin Assignments
Notes:
1. In OE or ST mode, a pull-up resistor of 10 kΩ or less is recommended if pin 1 is not externally driven. If pin 1 needs to be left floating, use the NC option.
̅ ̅̅
2. A capacitor of value 0.1 µF or higher between Vdd and GND is required.
Rev 1.06
Page 2 of 18
www.sitime.com
SiT8009B
High Frequency, Low Power Oscillator
Table 3. Absolute Maximum Limits
Attempted operation outside the absolute maximum ratings may cause permanent damage to the part. Actual performance
of the IC is only guaranteed within the operational specifications, not at absolute maximum ratings.
Parameter
Storage Temperature
Vdd
Electrostatic Discharge
Soldering Temperature (follow standard Pb free soldering guidelines)
Junction Temperature
[3]
Note:
3. Exceeding this temperature for extended period of time may damage the device.
Min.
-65
-0.5
–
–
–
Max.
150
4
2000
260
150
Unit
°C
V
V
°C
°C
Table 4. Thermal Consideration
[4]
Package
7050
5032
3225
2520
2016
JA, 4 Layer Board
(°C/W)
142
97
109
117
152
JA, 2 Layer Board
(°C/W)
273
199
212
222
252
JC, Bottom
(°C/W)
30
24
27
26
36
Note:
4. Refer to JESD51 for
JA
and
JC
definitions, and reference layout used to determine the
JA
and
JC
values in the above table.
Table 5. Maximum Operating Junction Temperature
[5]
Max Operating Temperature (ambient)
70°C
85°C
Maximum Operating Junction Temperature
80°C
95°C
Note:
5. Datasheet specifications are not guaranteed if junction temperature exceeds the maximum operating junction temperature.
Table 6. Environmental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Moisture Sensitivity Level
Condition/Test Method
MIL-STD-883F, Method 2002
MIL-STD-883F, Method 2007
JESD22, Method A104
MIL-STD-883F, Method 2003
MSL1 @ 260°C
Rev 1.06
Page 3 of 18
www.sitime.com
SiT8009B
High Frequency, Low Power Oscillator
Test Circuit and Waveform
[6]
Vdd
Vout
Test Point
tr
4
Power
Supply
0.1 uF
1
2
3
15pF
(including probe
and fixture
capacitance)
tf
80% Vdd
50%
20% Vdd
High Pulse
(TH)
Period
Low Pulse
(TL)
Vdd
OE/ST Function
1 kΩ
Figure 2. Test Circuit
Note:
6. Duty Cycle is computed as Duty Cycle = TH/Period.
Figure 3. Waveform
Timing Diagrams
90% Vdd
Vdd
Vdd
50% Vdd
T_resume
Pin 4 Voltage
T_start
No Glitch
during start up
[7]
ST Voltage
CLK Output
HZ
T_start: Time to start from power-off
CLK Output
HZ
T_resume: Time to resume from ST
Figure 4. Startup Timing (OE/ ST̅ Mode)
̅ ̅
Figure 5. Standby Resume Timing ( ST̅ Mode Only)
̅ ̅
Vdd
50% Vdd
OE Voltage
T_oe
Vdd
OE Voltage
50% Vdd
T_oe
CLK Output
HZ
T_oe: Time to re-enable the clock output
CLK Output
HZ
T_oe: Time to put the output in High Z mode
Figure 6. OE Enable Timing (OE Mode Only)
Figure 7. OE Disable Timing (OE Mode Only)
Note:
7. SiT8009 has “no runt” pulses and “no glitch” output during startup or resume.
[size=3][color=#323232][font=myFont, "]Humanity’s thirst for high-speed mobile data is endless. However, in urban environments, the available RF spectrum is already saturated, and it is clear that the...
[size=4][color=#454545][font=tahoma, helvetica, arial]In DSP, there are many places where you need to jump during program execution, so you need the target address of the jump. If you know the address...
I'm a newbie, and I need help from my friends: The problem is as follows: The CE1 pin of the TMS320VC5502 chip is connected to the Flash of the S29AL008. I want to know which part of the following ini...
O. Introduction
This system effectively combines the microcontroller and FPGA to realize equal-precision frequency measurement and IDDS technology, giving full play to their respective advanta...[Details]
Last week, Su Laoshi wrote an article called "LCD has fallen behind Germany's Bosch's first mass-produced 3D instrument panel debuted", which resonated a lot. It simply said that as cars become more ...[Details]
0 Introduction
The purpose of monitoring the hydraulic parameters of hydropower units in a hydropower station is first to ensure the safe and economical operation of the hydropower station, and se...[Details]
The content is based on the speech delivered by He Hao, President of Platform Technology System of SERES Group Co., Ltd. at the First China (Chongqing) Intelligent Vehicle Basic Software Ecosystem ...[Details]
★Xiaomi responds to the suspicion of plagiarism of Mimoji: On June 30, Xiaomi's spokesperson issued a statement on the official Weibo account, saying that they noticed a discussion initiated by a Wei...[Details]
On August 26, the first batch of power batteries of Yichang Hualin Titanium New Energy Co., Ltd. rolled off the production line in Xiaoting. This marks that Xiaoting District has taken a solid step in...[Details]
To port SQLite-3.3.12 to the ARM2410 development board, in addition to the support of the underlying operating system, you must also have the corresponding cross-compilation tool chain. Since the ARM2...[Details]
Front-facing cameras are an important component of advanced driver assistance systems (ADAS), especially given that new car crash tests now require automatic emergency braking and frontal collision a...[Details]
Magnesium batteries have long been considered an ideal alternative to lithium batteries because they are safer and less expensive, but their development has been limited by their limited capacity. ...[Details]
As the price of readers and tags decreases and the global market expands, the application of radio frequency identification (RFID) is increasing day by day. Tags can be powered by readers (passive ...[Details]
With the development of modern electronic technology, electronic devices are becoming increasingly portable and multifunctional, which puts forward the requirements for their power supply batteries...[Details]
There are two timers in the 51 microcontroller, namely timer 0 and timer 1. Timer 0: Timer 0 is an 8-bit timer, which can be used as a timer or counter. In timer mode, it can generate interrupt...[Details]
The Field Strength & Power Estimator iPhone app designed by Rohde & Schwarz (R&S) estimates the power flux density, the transmitted power of the electric and magnetic fields, and the gain of the tr...[Details]
Preface This is a new picture of development that is a mixture of the old and the new, and a transformation of kinetic energy. In the tall red brick factory building with a sense of age, red hot molte...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
