EEWORLDEEWORLDEEWORLD

Part Number

Search

10-214822-23K

Description
MIL Series Connector, 8 Contact(s), Composite, Male, Crimp Terminal
CategoryThe connector    The connector   
File Size493KB,72 Pages
ManufacturerDefense Logistics Agency
Download Datasheet Parametric View All

10-214822-23K Overview

MIL Series Connector, 8 Contact(s), Composite, Male, Crimp Terminal

10-214822-23K Parametric

Parameter NameAttribute value
Objectid1131052685
Reach Compliance Codeunknown
Other featuresSTANDARD: MIL-C 5015
Connector typeMIL SERIES CONNECTOR
Contact point genderMALE
Coupling typeTHREADED
Environmental characteristicsENVIRONMENT RESISTANT
MIL complianceYES
Manufacturer's serial number10-2148
Mixed contactsNO
Shell surfaceCADMIUM OVER NICKEL
Shell materialCOMPOSITE
Housing size22
Termination typeCRIMP
Total number of contacts8
INCH-POUND
MIL-DTL-5015H
18 May 2000
SUPERSEDING
MIL-C-5015G
AMENDMENT 5
15 March 1994
DETAIL SPECIFICATION
CONNECTORS, ELECTRICAL, CIRCULAR THREADED, AN TYPE,
GENERAL SPECIFICATION FOR
This specification is approved for use by all Departments and Agencies of the Department of
Defense.
1. SCOPE
1.1 Scope. This specification covers circular threaded electrical connectors with solder or
removable crimp contacts (both front and rear release). These connectors are for use in
electronic, electrical power, and control circuits (see 6.1).
1.2 Classification. Electrical connectors covered by this specification are divided into the
following classes, series, and receptacle styles.
1.2.1 Classes. The classes of electrical connectors are as follows:
Class A
Class B
Class C
Class D
Class DJ
-
-
-
-
-
Solid shell solder contact connectors
Split shell solder contact connectors
Solder contact connectors for use with pressurized equipment
Crimp and solder contact connectors for use in high-impact shock conditions
Crimp contact connectors with backshell connector assembly for use in high
impact shock conditions
Beneficial comments (recommendations, additions, deletions) and any pertinent data which
may be of use in improving this document should be addressed to: Commander, Naval Air
Warfare Center Aircraft Division, Systems Standardization Division, Code 414100B120-3,
Highway 547, Lakehurst, NJ 08733-5100, by using the Standardization Document
Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter.
AMSC N/A
FSC 5935
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
Technical article | How to use J-Link to burn SPI Flash
J-Link not only supports the burning of the Flash on the MCU , but also can directly burn the SPI Flash through the SPI protocol. Because the SPI protocol is used , even if the MCU connected to the SP...
MamoYU Integrated technical exchanges
Low power consumption comparison between STM8L and MSP430
After comparing actual products, STM8L's low power consumption is far better than MSP430. I'll record it here. Different opinions are welcome. The test environment is as follows: 1. External crystal o...
Aguilera Microcontroller MCU
Pengfeng Technology RVBoards-Nezha (RISC-V SBC) Allwinner Development Board Introduction 4
Perf-V IDE Introduction and Installation Instructions...
火辣西米秀 Domestic Chip Exchange
Share the SPWM code written by DSPF28335 with everyone
The source program is as follows:/** main.c*/ #include "DSP28x_Project.h"// Device Headerfile and Examples Include File // Prototype statements for functions found within this file. void InitEPwm1Exam...
fish001 DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号