*RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011.
Specifications are subject to change without notice.
The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.
Users should verify actual device performance in their specific applications.
Specifications are subject to change without notice.
The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.
Users should verify actual device performance in their specific applications.
PTD90 Series - 9 mm Multi-Ganged Potentiometer
Product Dimensions
SHAFT STYLE
"K"
L
±
0.5
(.020)
1.5
(.059)
A
18 TEETH
KNURL
How To Order
SHAFT STYLE
"F"
L
±
B
F
0.5
(.020)
PTD90 1 - 2 0 20 K - B 203
Model
• PTD90 =
No Switch
No. of Sections
• 1 = 1 Section
• 2 = 2 Sections
• 3 = 3 Sections
• 4 = 4 Sections
• 5 = 5 Sections
• 6 = 6 Sections
• 8 = 8 Sections
Pin Style
• 1 = PC Pins vertical/
down facing
and ±10 %
Total Resistance
Tolerance
•2=
6.5
±
0.3
(.256
±
.012)
B
1.0
(.039)
6.0 +0/-0.1
(.236 +0/-.004)
DIA.
30
°
9.5
±
0.3
(.374
±
.012)
6.0
(.236)
4.8
±
0.3
(.189
±
.012)
9.5
±
0.3
(.374
±
.012)
4.5
(.177)
4.5
(.177)
6.0 +0/-0.1
(.236 +0/-.004)
DIA.
60
°
4.8
±
0.3
(.189
±
.012)
6.5
±
0.3
(.256
±
.012)
0.8
(.031)
2.0
(.079)
0.8
(.031)
6.0
(.236)
3.5
(.138)
5.0
(.197)
0.8
(.031)
2.0
(.079)
0.8
(.031)
PC Pins vertical/
down facing
and ±20 %
Total Resistance
Tolerance
3.5
(.138)
5.0
(.197)
Center Detent Option
• 0 = No Detent
• 2 = Center Detent
Standard Shaft Length
• 15 = 15 mm
• 20 = 20 mm
• 25 = 25 mm
Shaft Styles
• K = Knurled Type Shaft (Metal)
18 Toothed Serration Type
• F = Flatted Metal Shaft
Resistance Taper (See Taper Charts)
Taper Series followed by Curve Number
Resistance Code (See Table)
Other shaft styles available.
SHAFT SHOWN IN CCW POSITION
SHAFT SHOWN IN CCW POSITION
L
B
A
15
(.591)
5
(.197)
6
(.236)
20
(.787)
7
(.276)
10
(.394)
25
(.984)
10
(.394)
12
(.472)
L
B
F
15
(.591)
5
(.197)
7
(.276)
20
(.787)
7
(.276)
12
(.472)
25
(.984)
10
(.394)
12
(.472)
DIMENSIONS:
MM
(INCHES)
Tapers
A Series Tapers
100
90
80
Terminal 1-2 Output Voltage
X 100 (%)
Terminal 1-3 Input Voltage
70
60
50
40
30
20
10
A6
A5
):
:
0A
A)
(3
(25
A4
A):
20
): A3
(
A
(15
A
A):
(10
A): A1
(05
B Series Tapers
100
(5B
): B
): B
5
4
(3B
): B
(2B
3
): B
2
(B
):
(1B
B
):
B
1
C Series Tapers
100
90
80
Terminal 1-2 Output Voltage
X 100 (%)
Terminal 1-3 Input Voltage
70
60
50
40
30
20
10
(3
(25 0C):
C
C
(20 ): C 6
5
(15 C):
C) C4
:
(1 C3
(05 0C):
C
C)
:C
1
90
80
Terminal 1-2 Output Voltage
X 100 (%)
Terminal 1-3 Input Voltage
70
60
50
40
30
20
10
0
10
20
30
40
50
60
70
80
90
100
(4B
0
10
20
30
40
50
60
70
80
90
100
0
10
20
30
40
50
60
70
80
90
100
Rotational Travel (%)
Rotational Travel (%)
Rotational Travel (%)
REV. 01/14
Specifications are subject to change without notice.
The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.
Users should verify actual device performance in their specific applications.
[i=s]This post was last edited by xusiwei1236 on 2022-6-25 23:40[/i]This article will introduce what TFLM is, then introduce the official TFLM benchmark, and how to run the TFLM benchmark on the HPM67...
[size=4]1. The filtering effect of capacitors[/size] [align=center][size=4] [/size][/align][size=4]That is, the larger the frequency f, the smaller the impedance Z of the capacitor. [/size] [size=4]Wh...
The figure shows the signal before the logic analyzer collects the 485 chip. The CS signal does not wrap the entire TX frame. The CS pull-up and pull-down settings are set before and after sending....
Some experience in Bluetooth configuration, suitable for novices to quickly get started!Summary of Bluetooth configuration experience- Taking HC05 and HC06 as examples - Author: Zhang Xinbin
1. Prepar...
Domestic Chip Exchange
京公网安备 11010802033920号
EEWORLD
