177-710-2-100GS4J5-18MTN datasheet, PDF

Datasheet> All Categories > The connector> Connector bracket> 177-710-2-100GS4J5-18MTN

177-710-2-100GS4J5-18MTN: DescriptionCable Assembly, 24AWG,; CategoryThe connector Connector bracket; File Size858KB，5 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/; Environmental Compliance

Download Datasheet Parametric View All

177-710-2-100GS4J5-18MTN Overview

Cable Assembly, 24AWG,

177-710-2-100GS4J5-18MTN Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	7004860465
Reach Compliance Code	compliant
Other features	STANDARDS: MIL-DTL-83513, MIL-W-22759/33
Certification	MIL
Conductor surface treatment	SILVER
conductor material	COPPER
ConnectorSide1	SOCKET CONNECTOR
ConnectorSide2	SOCKET CONNECTOR
Connector bracket type	CABLE ASSEMBLY
insulator material	EXTRUDED CROSSLINKED TEFZEL
Jacket material	E-CTFE HALAR EXPANDO
length	0.42 mm
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
shield	YES
Wire gauge	24 AWG

Preview

Download Datasheet

View All

SHIELDING EFFECTIVENESS (Db)

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

SHIELDING EFFECTIVENESS (Db)

Micro-D Harness

EMI Performance with Ground Spring

100

1.00E+03

MWDM Micro-D

Shielded Cable Assembly

Single-Ended or Double-Ended–These

easy-to-order cable

assemblies eliminate the need for expensive assembly labor. 100%

tested and ready for use.

Now With Twisted Pairs–No

need to create a procurement

specification for Micro-D cables with twisted pairs. Glenair 177-740

cables are furnished with a full complement of white/blue twisted

pair wires.

Integral Shield Termination–The

connector shell has a platform

to accept Band-It shield termination bands. The cable shield braid is

attached directly to the connector.

Save Labor, Reduce Weight and Improve EMI Shielding

with Glenair’s Micro-D Shielded Cable Assemblies

Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s

fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-

piece connector shell and secured with a stainless steel

Band-Master™ ATS

clamp. These pre-wired, 100% tested

assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low

shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be

ordered in any length, either single-ended or “back-to-back”.

Ground Spring and EMI Shielding Effectiveness

A gold-plated stainless steel ground spring on the pin connector mating

face offers substantial improvement in EMI protection. The graphs

compare identical connectors tested with and without ground springs.

EMI Performance without Ground Spring

100

1.00E+03

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

frequency (Hz)

High Performance Micro-D Connectors and Cables

U.S. CAGE Code 06324

Printed in U.S.A.

GLENAIR, INC.

•

1211 AIR WAY

•

GLENDALE, CA 91201-2497

•

818-247-6000

•

FAX 818-500-9912

www.glenair.com

B-14

E-Mail: sales@glenair.com

Recommended Resources

Low-cost high-precision instrument amplification circuit diagram

SAA1064 serial I2C bus LED dynamic driver interface circuit diagram

automatic ringer circuit

RS232 interface circuit

Optical communication receiving circuit

How to use 74LS138 cascade to form an addressing space of 000~1FF?

Review Weekly Report 20221010: Sipeed GW2A FPGA development board and Renesas ultra-low power MCU RA2L1 are here~: Activities currently being applied for1. Sipeed GW2A FPGA development board ( newly launched ) After being evaluated and praised by engineers in our forum, the domestic Gaoyun FPGA is coming again. Th...; EEWORLD社区 Special Edition for Assessment Centres

Why can a Zener diode break down with a reverse current of just a few volts, but a rectifier diode cannot break down with a reverse current of more than 200 volts?: [i=s]This post was last edited by Shenzhen Xiaohua on 2021-2-1 21:35[/i]Why can a Zener diode break down at a reverse current of just a few volts, but a rectifier diode cannot break down at a reverse ...; 深圳小花 MCU

Semiconductor Recruitment-Shanghai, Shenzhen, Hangzhou: Workplace: Shanghai, Hangzhou, Shenzhen Currently recruiting positions 1. AI algorithm R&D expert - IOT chip 2. Embedded software testing expert - IOT chip 3. Linux operating system R&D expert 4. Inte...; EmilyDuan Talking about work

Things to note when configuring 4G router ports: Industrial 4G routers have multiple ports. Here are some precautions for configuring their synchronous serial ports and Ethernet ports.(1) Industrial 4G router port IP address configuration. Each port...; 蓝先生 Industrial Control Electronics

Four major reasons for the heating of power modules: [p=null, 2, left][color=rgb(63, 63, 63)][font="][size=14px]When you touch the surface of the power module[color=#868686], it feels hot. Is the module broken? Wait a minute, it is a little hot, just be...; 仪商城 Integrated technical exchanges

[Erha Image Recognition Artificial Intelligence Vision Sensor] 3. Serial communication with the processor: I originally planned to use the I2C interface of the imx6ull development board to conduct a communication experiment with Erha Image Recognition. I happened to be using the serial port communication o...; dql2016 Domestic Chip Exchange

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components