XCTN26348100C datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> The resistor> XCTN26348100C

XCTN26348100C: DescriptionRES NET,THIN FILM,4.81K OHMS,100WV,.2% +/-TOL,-10,10PPM TC,0303 CASE; CategoryPassive components The resistor; File Size118KB，3 Pages; ManufacturerVishay; Websitehttp://www.vishay.com

Download Datasheet Parametric View All

XCTN26348100C Overview

RES NET,THIN FILM,4.81K OHMS,100WV,.2% +/-TOL,-10,10PPM TC,0303 CASE

XCTN26348100C Parametric

Parameter Name	Attribute value
Objectid	1171479407
package instruction	SMT, 0303
Reach Compliance Code	unknown
ECCN code	EAR99
structure	Chip
Manufacturer's serial number	CTN
Network Type	Center Tap
Number of terminals	6
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package height	0.254 mm
Package length	0.762 mm
Package form	SMT
Package width	0.762 mm
method of packing	Tray
Rated power dissipation(P)	0.25 W
Guideline	MIL-STD-883
resistance	4810 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	CTN
size code	0303
Temperature Coefficient	10 ppm/°C
Tolerance	0.2%
Operating Voltage	100 V

Preview

Download Datasheet

View All

CTN

Vishay Electro-Films

Nichrome Thin Film, Center Tapped Resistors

CHIP

RESISTORS

FEATURES

•

Wire bondable

Product may not

be to scale

•

Center tap feature

•

Chip size: 0.030 inches square

•

Resistance range total: 10

to 1 MΩ

•

Ratio tolerances to: 0.1 %

•

Resistor material: Nichrome

•

Oxidized silicon substrate for good power dissipation

The CTN series is a center tapped nichrome resistor chip

providing excellent stability at 250 mW power levels. The

CTN offers the designer flexibility in use as either a single

value resistor or as two resistors with a center tap feature.

The CTNs six bonding pads allows the user increased layout

flexibility.

The CTNs are manufactured using Vishay Electro-Films

(EFI) sophisticated thin film equipment and manufacturing

technology. The CTNs are 100 % electrically tested and

visually inspected to MIL-STD-883.

APPLICATIONS

The CTN center-tapped resistor chips are used mainly in feedback circuits of amplifiers where ratio matching, high power and

tracking between two resistors is critical.

Recommended for Hermetic environment where die is not exposed to moisture.

For low values, the resistance of the six bonding-pad configurations can vary, depending on the method of measurement used.

Vishay EFI measures low-value resistors by the four wire Kelvin technique.

TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES AND TOLERANCES

Tightest Standard Tolerance Available

0.5 %

0.1 %

± 10 ppm/°C

± 25 ppm/°C

± 50 ppm/°C

± 100 ppm/°C

PROCESS CODE

CLASS H*

203

202

200

201

*MIL-PRF-38534 inspection criteria

1 MΩ

CLASS K*

263

262

260

261

100

200

1 kΩ

STANDARD ELECTRICAL SPECIFICATIONS

PARAMETER

TCR Tracking Between Halves (R

)

Center Tap Ratio,

Tolerance

Noise, MIL-STD-202, Method 308, 100

- 250 kΩ

Stability, 1000 h, + 125 °C, 125 mW

Operating Temperature Range

Dielectric Voltage Breakdown

Insulation Resistance

Operating Voltage

DC Power Rating at + 70 °C (Derated to Zero at + 175 °C)

* 20 ppm/°C for

< 20

www.vishay.com

For technical questions, contact: efi@vishay.com

Document Number: 61024

Revision: 12-Mar-08

± 2 ppm/°C *

1 ± 1 % standard

- 35 dB typ.

± 0.1 %

ΔR/R

- 55 °C to + 125 °C

200 V

min.

100 V max.

250 mW

Recommended Resources

Digital display electric heating furnace automatic temperature controller

LCD interface circuit

DC exciter excitation mode circuit

Use transfer switch control

Typical application circuit without precharge function using MAX1894/MAX1924

1MHz square wave double frequency: How can I double the frequency of a 1MHz signal? Is there a direct chip that can achieve this? I don't want to use a phase-locked loop + divider because the function is not complicated....; sudongpo2018 Analogue and Mixed Signal

CC3200 Modify the sprinkler routine of Out of Box: [i=s]This post was last edited by littleshrimp on 2019-1-4 17:59[/i] In the sprinkler example provided by the official Out of Box, the image update and the LED flashing of the development board will b...; littleshrimp Wireless Connectivity

Upgrading the embedded RISC-V compiler: The ch32v103c8t6 board was developed using the MounRiver Studio tool. The integration of this tool is good, but the project templates are a bit "simple". It seems that it is a bit confusing to study t...; bigbat Domestic Chip Exchange

You can use FIND to check which library a certain component is in in the PROTEL schematic. You can also check which library a certain package is in. Why is it not there?: [i=s]This post was last edited by Yishayishi on 2022-9-28 09:59[/i]In PROTEL99, you can use the FIND button in the figure below to find which library a component in the schematic diagram is in, but wh...; 一沙一世 stm32/stm8

Can RS485 communicate stably using parallel wires (non-twisted pair)? 5m wire length, 9600bps: We are working on a field environmental monitoring project, where the communication terminal and data acquisition terminal communicate via 485. The power supply and 485 signal line share a cable. I wo...; zhangbaoxiang Test/Measurement

TI Wired and Wireless Communications in Electric Vehicle Battery Management: ...; Jacktang Wireless Connectivity

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components