EEWORLDEEWORLDEEWORLD

Part Number

Search

CC1-27100BESSNHWS

Description
Fixed Resistor, Thin Film, 0.04W, 2710ohm, 100V, 0.1% +/-Tol, -25,25ppm/Cel, 0204,
CategoryPassive components    The resistor   
File Size70KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

CC1-27100BESSNHWS Overview

Fixed Resistor, Thin Film, 0.04W, 2710ohm, 100V, 0.1% +/-Tol, -25,25ppm/Cel, 0204,

CC1-27100BESSNHWS Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid987088259
Reach Compliance Codeunknown
ECCN codeEAR99
structureChip
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length0.5 mm
Package formSMT
Package width1 mm
method of packingWaffle Pack
Rated power dissipation(P)0.04 W
resistance2710 Ω
Resistor typeFIXED RESISTOR
seriesCC1
size code0204
technologyTHIN FILM
Temperature Coefficient-25,25 ppm/°C
Tolerance0.1%
Operating Voltage100 V
CC1-
www.vishay.com
Vishay Electro-Films
Thin Film 0402 Size Resistor on Alumina
FEATURES
Product may not be to scale
Wire bondable
Small single chip size: 0.020" x 0.040"
Case: 0402
Resistance range: 10
to 24 k
Alumina substrate
Low stray capacitance: < 0.2 pF
Resistor material: Nichrome
Resistor passivation coat optional
Solder Pads optional
The CC1- series single-value resistor chips offer a small
size, low shunt capacitance and solder pad option. The
CC1- nichrome resistors material offers excellent stability.
The CC1- resistors are manufactured using Vishay
Electro-Films (EFI) sophisticated thin film equipment and
manufacturing technology. The CC1- resistors are 100 %
electrically tested and visually inspected to MIL-STD-883.
APPLICATIONS
Vishay EFI CC1- chip resistors provide excellent
high-frequency response and are ideally suited for
prototyping.
Typical application areas are:
• Amplifiers
• Oscillators
• Attenuators
• Couplers
• Filters
Recommended for hermetic environments where die is not
exposed to moisture.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES, AND TOLERANCES
PARAMETER
Total Resistance Range
Standard Tolerances
TCR
Tightest Standard Tolerance Available
0.5 %
0.1 %
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
VALUE
10 to 24K
± 0.05, ± 0.1
± 25, ± 50, ± 100
UNIT
%
ppm/°C
10
Ω
20
Ω
200
Ω
12 kΩ
24 kΩ
Note
• Only 25
to 1 k are standard strip line designs for microwave applications
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
Noise, MIL-STD-202, Method 308
Moisture Resistance, MIL-STD-202, Method 106 - Hermetic
applications
Stability, 1000 h, + 125 °C, 40 mW
Operating Temperature Range
Thermal Shock, MIL-STD-202, Method 107, Test Condition F
High Temperature Exposure, + 150 °C, 100 h
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 125 °C (Derated to Zero at + 150 °C)
5 x Rated Power Short-Time Overload, + 25 °C, 5 s
Revision: 18-Aug-11
1
For technical questions, contact:
efi@vishay.com
VALUE
- 20 typ.
± 0.2 max.
R/R
± 0.1 max.
R/R
- 55 to + 125
± 0.25 max.
R/R
± 0.1 max.
R/R
400
10
12
min.
100 max.
0.040 max.
± 0.25 max.
R/R
UNIT
dB
%
%
°C
%
%
V
V
W
%
Document Number: 61001
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Flathead RVB2601 creative application development] @fxyc87 RVB2601-Qiqiao technology
My history posts: [RVB2601 creative application development] @fxyc87 RVB2601 unboxing + hello_worldAs the saying goes, sharpening the knife does not delay the chopping of wood, so you can work better ...
fxyc87 XuanTie RISC-V Activity Zone
MOS Driver
Could you please tell me how to optimize this circuit so that its output waveform has less distortion?...
tangwei8802429 Analog electronics
Looking for a DC/DC step-down chip
Hello everyone, I now want to need a DC/DC step-down chip. The input requirement is DC20V 3.25A and the output is DC 3.4V 14A. If there is a constant source, it would be the best. Thank you. If you ha...
liushiming82 Power technology
Ask for advice from the experts! Design of soft start circuit based on single chip microcomputer
Recently, I want to design a three-phase soft start circuit based on a single-chip microcomputer. The basic components required are: 1.IGBT tube 2. Single chip microcomputer 3. Relay 4. Motor 5. LCD d...
电工新手求指导 Analog electronics
U disk IAP jump APP abnormal
[i=s]This post was last edited by shipeng on 2019-5-15 18:48[/i] [size=3]I recently used the USB_OTG_FS of STM32F429 to make a BOOTLOADER that can read files in the USB disk through USB (PA11, PA12) o...
shipeng stm32/stm8
Control power-on circuit problem
What is the problem with this circuit to realize the microcontroller control startup? Is the resistance of R2 too large?...
kal9623287 Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号