Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
[i=s] This post was last edited by bqgup on 2021-4-24 18:46 [/i] # MATLAB simulates network debugging assistant for UDP communication **Table of Contents** [TOCM] #1. Network debugging assistant UDP c...
[i=s]This post was last edited by Baboerben on 2022-4-20 16:33[/i]I don't have 1n5822 on hand, and I'm in a hurry to do the experiment. I use a transistor to replace the diode at 5822 as shown in the ...
Our company wants to make a washing machine that uses a brushless DC motor.The back EMF is a trapezoidal wave.
I bought a development board and the seller has a program, but he said the back EMF is a ...
[i=s]This post was last edited by dcexpert on 2022-8-3 21:37[/i]The reason I participated in the Digi-Key event this time was to prepare to make a portable programmable meter that is small in size and...
[i=s] This post was last posted by fish001 on 2018-8-27 20:25 Edit[/i] [size=4] In embedded development, older developers are more accustomed to using C language; and young people are also taught in C...
[i=s] This post was last edited by Renjianjingpin on 2020-7-22 11:36[/i]This solution is a method for implementing wireless Modbus communication between Kunlun Tongtai touch screen and four DTD433FC w...
The basic principle of PWM control
PWM (Pulse Width Modulation) is a commonly used control method that controls the working state of devices or components in a circuit by adjusting the pulse w...[Details]
Matching an antenna to an application requires accurate antenna measurements. Antenna engineers need to determine how an antenna will perform in order to determine if it is suitable for a particular a...[Details]
UPS is the abbreviation of uninterruptible power system. It is an important external device that can provide continuous, stable and uninterrupted power supply. UPS is divided into three categories ac...[Details]
IT Home reported on April 17 that the Linux 5.19 kernel has added multiple feature supports recently, one of which is the Raptor Lake-S graphics driver support in the kernel PCI ID part. Now, ...[Details]
l Introduction
Click-and-pop suppressors are standalone devices that can be added to a system late in the design process to eliminate clicks and pops without changing the original design. The M...[Details]
UltraSoC has won the Best of Show award in the security category from industry portal Embedded Computing at the Embedded World 2020 conference held in Munich, Germany not long ago. The Best of Show a...[Details]
According to 91mobiles, Nokia TV "55CAUHDN" will be officially launched as early as December this year. It is currently confirmed that this TV has a 55-inch 4K resolution, uses JBL speakers and run...[Details]
Ryan Sheahen, Global Product Manager, Magnetic Sensor Products, Electronics Business Unit, Littelfuse Even with today's energy-efficient designs, modern appliances, especially refrigerators and fre...[Details]
1. In order to ensure high measurement accuracy, the flow meter should be installed on a horizontal pipe, and the direction of the flow direction indicator arrow of the flow meter should be consistent...[Details]
Recently, according to foreign media reports, Singapore's telecommunications regulator IMDA disclosed two new realmi devices on its website - realme 5i and realme C3, whose model numbers are R...[Details]
MLCC (chip multilayer ceramic capacitor) has now become one of the most commonly used components in electronic circuits. MLCC seems very simple on the surface, but in many cases, design engineers or p...[Details]
There are many safety issues in electronic production that cannot be ignored. If you don't pay attention, it will cause irreversible serious consequences, which may damage the equipment or even cau...[Details]
MiR Fleet Enterprise is more than just a simple upgrade; it also brings modules that keep pace with customer needs and technological developments, as well as other advanced features.
Sha...[Details]
Innovation Lab
京公网安备 11010802033920号
EEWORLD
