FMXMB1360HID-27.000000M-PD datasheet, PDF

Datasheet> All Categories > Passive components> Crystal/resonator> FMXMB1360HID-27.000000M-PD

FMXMB1360HID-27.000000M-PD: DescriptionQuartz Crystal,; CategoryPassive components Crystal/resonator; File Size260KB，1 Pages; ManufacturerFrequency Management International; Environmental Compliance

Download Datasheet Parametric View All

FMXMB1360HID-27.000000M-PD Overview

Quartz Crystal,

FMXMB1360HID-27.000000M-PD Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	145048848467
package instruction	HC-49/US, 2 PIN
Reach Compliance Code	compliant
Ageing	5 PPM/YEAR
Crystal/Resonator Type	PARALLEL - 3RD OVERTONE
Drive level	50 µW
frequency stability	0.004%
frequency tolerance	30 ppm
load capacitance	60 pF
Installation features	THROUGH HOLE MOUNT
Nominal operating frequency	27 MHz
Maximum operating temperature	50 °C
Minimum operating temperature	-10 °C
physical size	L11.5XB4.65XH4.1 (mm)/L0.453XB0.183XH0.161 (inch)
Series resistance	120 Ω
surface mount	NO

Preview

Download Datasheet

View All

FMXMB

SERIES

Thru-hole Crystals

Low Profile

Thru-Hole Package

Multiple Package Heights

Low Cost

HC-49/US

SPECIFICATIONS

Issue 6 - 10182012

Parameter

Frequency Range

Operation Mode

Load Capacitance (CL)

Frequency Tolerance

Temperature Tolerance

Operating Temperature

Storage Temperature

Equivalent Series Resistance (ESR)

Shunt Capacitance (C0)

Drive Level

Aging @ 25°C

All specifications subject to change without notice.

Specification

3.2 - 90 MHz

See Operation Mode and ESR Table

18 pF Std., 8 - 60 pF and Series available

±30 ppm @ 25°C Std. (See Cal. Tol. for Options)

±50 ppm Std. (See Temp. Tol. for Options)

0 to +70°C Std. (See Temp. Range for Options)

-55 to +125°C

See Operation Mode and ESR Table

7 pF max.

50 uW typical, 1 mW max.

±5 ppm per year max.

HC-49/US

OPERATION MODE AND ESR TABLE

Frequency (MHz)

3.200 - 5.999

6.000 - 7.999

8.000 - 9.999

10.00 - 14.99

15.000 - 40.000

27.000 - 70.000

MODE

Fundamental

Overtone

MAX ESR (Ohms)

180

100

120

DIMENSION “H” TABLE

STANDARD MARKING

FMI XX.XXX

XX.XXX FREQUENCY in MHz

Package

Max. Height

0.161” (4.1mm)

0.126” (3.2mm)

0.118” (3.0mm)

NOTE: Standard Specifications for product indicated in

color

Dimensions:

Inches

(mm)

PART DESCRIPTION SYSTEM

MARKING: See Page 52, Format A

FMXM B1 1 18 H J A - XX.XXXXXXM - CM

Product Family

Crystal

Package

B1,

B2 or B3

Mode

1 - Fundamental

3 - 3rd Overtone

Load Cap. (CL)

18 - Standard (pF)

00 - Series

## - Custom (pF)

Cal.

Tol. @ 25°C

±10 ppm

±15 ppm

±20 ppm

±25 ppm

±30 ppm

±40 ppm

±50 ppm

Custom

*Temp. Tol.

D ±10 ppm

E ±15 ppm

F ±20 ppm

G ±25 ppm

H ±30 ppm

I ±40 ppm

J ± 50 ppm

X Custom

Frequency (MHz)

Temp. Range

A 0 to 70 °C

B -20 to 70 °C

C -40 to 85 °C

D -10 to 50 °C

E -10 to 60 °C

F -30 to 60 °C

J 0 to 50 °C

X Custom

Options

BI - Base Insulator

LT - Lead Trimming

LF - Lead Forming

PD - Parameter Data

TD - Temp. Data

CM - Custom Mark

BLANK - None Req’d.

**Check with us for availability.

-55°C TO +125°C Available, Limited Stability Options,

please consult the factory.

1-800-800-XTAL

[9825]

www.fmi-inc.com

Recommended Resources

TDA2030A subwoofer circuit diagram

Typical Schmitt trigger circuit diagram

Signal simulator circuit diagram

Tracking gate pulse generation circuit diagram

Current limited circuit diagram

Simple water level control circuit diagram

What is the function of the cross connection of the five tubes in the middle of this comparator?: What is the function of the cross-connection of the five tubes in the middle of this comparator? The test shows that it is a falling edge trigger. Where is the falling edge trigger? Please help. It wo...; 真让人头大55 Analog electronics

What is the difference between pyb.delay and time.sleep?: It’s still Xiaobai’s problem. When learning micropython, I came across pyb.delay and time.sleep, both of which can achieve delay. What is the difference between them, or what impact do they have on th...; ywb888 MicroPython Open Source section

Stepper motor current test: In the above figure, the red dotted line is the current on the motor phase line, and the blue line is the voltage on the phase line. The current probes from Tektronix and Keysight are too expensive an...; S3S4S5S6 Analog electronics

[RVB2601 creative application development] + light intensity detection: With the basic use of GPIO port, in addition to driving the OLED screen, it can also be used to drive the corresponding digital sensor. Here, the light intensity sensor is driven, and the display func...; jinglixixi XuanTie RISC-V Activity Zone

【DIY Creative LED】Effect Demonstration: [i=s]This post was last edited by dcexpert on 2020-10-6 18:16[/i]Let's first demonstrate the running effect, which is completely controlled by touch keys.Start : Touch both touch keys at the same time...; dcexpert MCU

[GD32450I-EVAL] USART and DMA variable length reception: [i=s] This post was last edited by tinnu on 2020-10-25 23:18[/i](1) Enable DMA The recommended DMA sending USART mode in the routine: void USART_DMA_Init(void) {dma_single_data_parameter_struct dma_in...; tinnu GD32 MCU

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components