EEWORLDEEWORLDEEWORLD

Part Number

Search

WBC-T0303AG-03-8561-DF

Description
Array/Network Resistor, Center Tap, Thin Film, 0.25W, 8560ohm, 100V, 0.5% +/-Tol, -25,25ppm/Cel, 0303,
CategoryPassive components    The resistor   
File Size376KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

WBC-T0303AG-03-8561-DF Overview

Array/Network Resistor, Center Tap, Thin Film, 0.25W, 8560ohm, 100V, 0.5% +/-Tol, -25,25ppm/Cel, 0303,

WBC-T0303AG-03-8561-DF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid802621416
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
resistance8560 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesWBC(TAPPED)
size code0303
technologyTHIN FILM
Temperature Coefficient-25,25 ppm/°C
Tolerance0.5%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC Advanced Film Division
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
R
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Back contact
Noise
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
Passivation
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Gold available)
Gold
3KÅ minimum
Silicon Dioxide or
Silicon Nitride
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
R
Top contact
pad chamfered
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
Backside
½R
½R
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue April 2006
X-NUCLEO-IKS02A1 Industrial Sensor Evaluation Board Data
An industrial sensor development board launched by ST, equipped with an Arduino UNO R3 connector, can be directly connected to the STM32 Nucleo development board or other development boards that suppo...
littleshrimp MEMS sensors
FAQ_About the pulse problem when the output port of BlueNRG-2 remains at a low level in low power mode
Author: Weisheng CHEN, ST engineer Click to download the pdf document:Keywords: BlueNRG-2, GPIO, port hold, pulse.Problem: Some customers have reported that in BlueNRG-2 applications, GPIO pins config...
nmg ST - Low Power RF
There are still some problems with the PCB diagram drawn by a novice
The thing is, I am designing a brushless motor control board, which is divided into the main control board and the power amplifier board. I have the main control board schematic diagram, but I can't d...
Hubble林 PCB Design
SparkRoad OV2640 FPGA evaluation board test
Today I tested OV2640, using the example program https://github.com/verimake-team/SparkRoad-V/tree/master/demo/16_ov2640_sdram, but the result was not very satisfactory. I have used this OV2640 before...
littleshrimp FPGA/CPLD
[Bluesun AB32VG1 RISC-V Evaluation Board] Problems encountered: USB and Bluetooth
Regarding most of the hardware functions of this development board, I have seen other friends in the forum and the official website forum of RTThread have already talked about it very well, so I will ...
Ansersion Domestic Chip Exchange
Can you share your experience of learning FPGA?
I encountered many setbacks while learning FPGA by myself. Of course, I feel better now after a long time. But I still can't find the way. My learning method and design ideas are basically like a blin...
lingking FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号