ST = GND, Vdd_2.8, Vdd_3.0, Vdd_3.3, Vdd_XX, Vdd_YY.
Output is weakly pulled down
ST = GND, Vdd_2.5, Output is weakly pulled down
ST = GND, Vdd_1.8, Output is weakly pulled down
1.07
10 March 2021
www.sitime.com
SiT8008B
Low Power Programmable Oscillator
Table 1. Electrical Characteristics
(continued)
Parameters
Duty Cycle
Rise/Fall Time
Symbol
DC
Tr, Tf
Min.
45
–
–
–
–
Output High Voltage
VOH
90%
Typ.
–
1
1.3
–
–
–
Max.
55
2
2.5
2
2.7
–
Unit
%
ns
ns
ns
ns
Vdd
Condition
All Vdds. See Duty Cycle definition in
Figure 3
and
Footnote 6
20% - 80% Vdd_2.5, Vdd_2.8, Vdd_3.0, Vdd_3.3
20% - 80% Vdd_1.8
20% - 80% Vdd_XX
20% - 80% Vdd_YY
IOH = -4 mA (Vdd_3.0 and Vdd_3.3)
IOH = -3 mA (Vdd_2.8 and Vdd_ 2.5)
IOH = -2 mA (Vdd _1.8)
IOH = -4 mA (Vdd_3.0 and Vdd_3.3)
IOH = -3 mA (Vdd_2.8 and Vdd_ 2.5)
IOH = -2 mA (Vdd _1.8)
Pin 1, OE or ST
Pin 1, OE or ST
Pin 1, OE logic high or logic low, or ST logic high
Pin 1, ST logic low
Measured from the time Vdd reaches its rated minimum value
f = 110 MHz. For other frequencies, T_oe = 100 ns + 3 * cycles
Measured from the time ST pin crosses 50% threshold
f = 75 MHz, Vdd_1.8, Vdd_2.5, Vdd_2.8, Vdd_3.0, Vdd_3.3,
Vdd_XX,
f = 75 MHz, Vdd_YY
f = 75 MHz, Vdd_2.5, Vdd_2.8, Vdd_3.0, Vdd_3.3, Vdd_XX, Vdd_YY
f = 75 MHz, Vdd_1.8
f = 75 MHz, Integration bandwidth = 900 kHz to 7.5 MHz. Vdd_1.8,
Vdd_2.5, Vdd_2.8, Vdd_3.0, Vdd_3.3, Vdd_XX
f = 75 MHz, Integration bandwidth = 12 kHz to 20 MHz. Vdd_1.8,
Vdd_2.5, Vdd_2.8, Vdd_3.0, Vdd_3.3, Vdd_XX
f = 75 MHz, Integration bandwidth = 900 kHz to 7.5 MHz. Vdd_YY
f = 75 MHz, Integration bandwidth = 12 kHz to 20 MHz. Vdd_YY
LVCMOS Output Characteristics
Output Low Voltage
VOL
–
–
10%
Vdd
Input Characteristics
Input High Voltage
Input Low Voltage
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
50
2
Startup Time
Enable/Disable Time
Resume Time
RMS Period Jitter
T_start
T_oe
T_resume
T_jitt
–
–
–
–
–
Peak-to-peak Period Jitter
RMS Phase Jitter (random)
T_pk
T_phj
–
–
–
–
–
–
–
–
87
–
–
–
–
1.8
–
12
14
0.5
1.3
–
–
–
30%
150
–
5
130
5
Jitter
3
3.3
25
30
0.9
2
1.4
2.3
ps
ps
ps
ps
ps
ps
ps
ps
Vdd
Vdd
k
M
ms
ns
ms
Startup and Resume Timing
Table 2. Pin Description
Pin
Symbol
Output Enable
1
OE/ST/NC
̅ ̅̅
Functionality
H
[1]
: specified frequency output
L: output is high impedance. Only output driver is disabled.
H
[1]
: specified frequency output
L: output is low (weak pull down). Device goes to sleep mode.
Supply current reduces to I_std.
Any voltage between 0 and Vdd or Open
[1]
: Specified frequency
output. Pin 1 has no function.
Electrical ground
Oscillator output
Power supply voltage
[2]
Top View
OE/ST/NC
̅ ̅̅
Standby
No Connect
2
3
4
GND
OUT
VDD
Power
Output
Power
Figure 1. Pin Assignments
Notes:
1. In OE or ST mode, a pull-up resistor of 10 kΩ or less is recommended if pin 1 is not externally driven. If pin 1 needs to be left floating, use the NC option.
̅ ̅̅
2. A capacitor of value 0.1 µF or higher between Vdd and GND is required.
1.07
Page 2 of 18
www.sitime.com
SiT8008B
Low Power Programmable Oscillator
Table 3. Absolute Maximum Limits
Attempted operation outside the absolute maximum ratings may cause permanent damage to the part. Actual performance
of the IC is only guaranteed within the operational specifications, not at absolute maximum ratings.
Parameter
Storage Temperature
Vdd
Electrostatic Discharge
Soldering Temperature (follow standard Pb free soldering guidelines)
Junction Temperature
[3]
Note:
3. Exceeding this temperature for extended period of time may damage the device.
Min.
-65
-0.5
–
–
–
Max.
150
4
2000
260
150
Unit
°C
V
V
°C
°C
Table 4. Thermal Consideration
[4]
Package
7050
5032
3225
2520
2016
Note:
4. Refer to JESD51 for
JA
and
JC
definitions, and reference layout used to determine the
JA
and
JC
values in the above table.
JA, 4 Layer Board
(°C/W)
142
97
109
117
152
JA, 2 Layer Board
(°C/W)
273
199
212
222
252
JC, Bottom
(°C/W)
30
24
27
26
36
Table 5. Maximum Operating Junction Temperature
[5]
Max Operating Temperature (ambient)
70°C
85°C
Maximum Operating Junction Temperature
80°C
95°C
Note:
5. Datasheet specifications are not guaranteed if junction temperature exceeds the maximum operating junction temperature.
Table 6. Environmental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Moisture Sensitivity Level
Condition/Test Method
MIL-STD-883F, Method 2002
MIL-STD-883F, Method 2007
JESD22, Method A104
MIL-STD-883F, Method 2003
MSL1 @ 260°C
1.07
Page 3 of 18
www.sitime.com
SiT8008B
Low Power Programmable Oscillator
Test Circuit and Waveform
[6]
Vdd
Vout
Test Point
tr
4
Power
Supply
0.1 uF
1
2
3
15pF
(including probe
and fixture
capacitance)
tf
80% Vdd
50%
20% Vdd
High Pulse
(TH)
Period
Low Pulse
(TL)
Vdd
OE/ST Function
1 kΩ
Figure 1. Test Circuit
Note:
6. Duty Cycle is computed as Duty Cycle = TH/Period.
Figure 2. Waveform
Timing Diagrams
90% Vdd
Vdd
Vdd
50% Vdd
[7]
Pin 4 Voltage
T_start
No Glitch
during start up
ST Voltage
T_resume
CLK Output
HZ
T_start: Time to start from power-off
CLK Output
HZ
T_resume: Time to resume from ST
Figure 3. Startup Timing (OE/ ST̅ Mode)
̅ ̅
Figure 4. Standby Resume Timing ( ST̅ Mode Only)
̅ ̅
Vdd
50% Vdd
OE Voltage
T_oe
Vdd
OE Voltage
50% Vdd
T_oe
CLK Output
HZ
T_oe: Time to re-enable the clock output
CLK Output
HZ
T_oe: Time to put the output in High Z mode
Figure 5. OE Enable Timing (OE Mode Only)
Note:
7. SiT8008 has “no runt” pulses and “no glitch” output during startup or resume.
[i=s]This post was last edited by gs001588 on 2021-12-15 01:28[/i]I have received the development board for a few days and have tested several programs. The development environment is relatively frien...
Brush plating technology has been researched, developed, applied and promoted in my country for more than 20 years. This new technology has solved key problems such as maintenance in many national key...
Dear experts, I am using KiCad 5. The default design rules have not been changed. Some chip pins will bend when they are connected. I have to press the / key to make them straight. Do I need to set it...
[i=s]This post was last edited by Hot Ximixiu on 2021-6-23 08:18[/i]For users who are new to MM32 MCU, they may encounter the situation that the MCU cannot be downloaded, and then report that there is...
Goodbye 20192019 was a special year. I was busy the whole year, and I gained a lot, both unexpectedly and reasonably. There were also personal and organizational reasons (although I still haven’t reco...
In today's
industrial automation
field,
collaborative robots
have become an emerging force that cannot be ignored. As a leader in this field, Universal
Robots
recently annou...[Details]
The steer-by-wire system is an automotive electronic technology related to safety. By eliminating the hard connection between the front wheel and the steering wheel, an electrical signal is generat...[Details]
When making a microcomputer monitoring system, if the monitored object itself is also a microcomputer system and there is no circuit diagram, program and other information, how to collect the internal...[Details]
As Apple pushed the official version of iOS 14.2 to users last week, they officially stopped signing iOS 14.1 and iPadOS 14.1 today, which means that users who updated their devices to iOS 14.2 can n...[Details]
Satcon Technology, a renewable energy solutions provider, recently announced that it has signed a strategic manufacturing agreement with Sanmina-SCI. Under this agreement, Sanmina will produce its ...[Details]
In order to promote the high-quality development of my country's energy and implement the key tasks of the "Guiding Opinions on Promoting the Development of Energy Storage Technology and Industry" ...[Details]
As the industry's first truly open source processor architecture, RISC-V has attracted much attention since its launch. For the industry, the impact it has brought to the industry and the ecosystem i...[Details]
Autonomous driving is not coming as fast as imagined. Recently, Zhang Yufeng, vice president of Horizon and vice president of Auto product line, said that L3 autonomous driving will not be available ...[Details]
0 Introduction In situations where environmental conditions are demanding, it is necessary to precisely measure relative humidity and temperature. For this purpose, an intelligent high-precision rela...[Details]
The world's first powered mechanical car was a steam-driven three-wheeled car made by Frenchman N.J. Cugnot in 1769. It is regarded as a watershed between ancient transportation (powered by people, a...[Details]
On December 20, according to domestic media reports, a British team recently developed an electrocardiogram imaging vest that can more accurately predict patients' risk of sudden cardiac death, the...[Details]
At present, many oscilloscope manufacturers have launched MSO oscilloscopes (mixed signal oscilloscopes), but the products on the market are of varying quality and it is difficult for ordinary users ...[Details]
As the mobile market such as mobile phones and tablets continues to be popular, ARM's low-power and high-efficiency core technology has received more and more attention. Major domestic companies have ...[Details]
Reference voltage input A simplified schematic of a successive approximation ADC is shown in Figure 1. During the sampling interval, a capacitive DAC is connected to the ADC input and a charge propor...[Details]
Security and anti-theft have become social issues. Locks have been guarding the door since ancient times. People have high requirements for them. They must be safe and reliable against theft and ...[Details]
Domestic Chip Exchange
京公网安备 11010802033920号
EEWORLD
