Above ratings are based on the thermal resistances using a multi-layer circuit board (EIA/JESD51). For mounting on a mono-layer board, power derating shall be
needed. Please inquire of us about conditions.
※1 素子毎の負荷電力の合計が、パッケージ定格電力を超えない条件で御½用ください。
※1 Total power consumption of all elements should not exceed the package power rating.
The resistor of this product is formed by narrow patterning a thin metal film. Thus, application of excessive voltage causes burn and destruction of the resistive film, abnormality
in resistance or open resistance and loss of proper function. The properly and electrostatically measured taping materials are used for the components, but attention should be paid
to the fact that there is some danger the parts may be destructed by static electricity(equivalent to 500V or over at 100pF, 1.5kΩ) to cause a change in resistance in the conditions
of an excessive dryness when mounting on the boards. Similarly, care should be given not to apply the excessive static electricity at the time of mounting on the boards. When
designing, consideration can be taken into withstanding ESD for customized KPC products. Please consult with us about the details.
●
Hand soldering by iron soldering or repairment are not recommended because KPC is a multi-pin product.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. In the case of 5〜35℃/35〜75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas
like hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
The third generation of anti-noise products in China currently use dynamic noise reduction ( DNR ) technology. DNR technology dynamically adjusts the output voice switch through the changing voice pea...
Hello everyone!
I recently received quotes from several OEMs, and two of them specified Ethernet connectors, but did not specify other connectors. I would like to ask the experts in vehicle architectu...
I found a motherboard labeled as a shared bicycle control board on Xianyu. It was cheap, only 8 yuan, so I bought a few to play with. I haven't received the goods yet. I hope to learn some technologie...
Recently, the teacher asked me to make a minimum FPGA system. The minimum system uses JTAG debugging and downloading, and AS is used for fixed downloading. After it was completed, I found that JTAG ca...
NVH testing has become a comprehensive issue to measure the quality of automobile manufacturing, and it gives the most direct and superficial experience to car users.
The NVH problem of vehicles is on...
As people's awareness of energy conservation and environmental protection grows, the industry is paying more and more attention to the impact of energy consumption on the environment. Among variou...[Details]
Abstract: Design a MMS alarm system based on GPRS and 51 single-chip microcomputer. Utilize single-chip microcomputer technology, GPRS wireless communication module with MMS protocol, image capture...[Details]
On August 1, the Ministry of Industry and Information Technology announced that the "Implementation Plan for Carbon Peaking in the Industrial Sector" jointly issued by the Ministry of Industry and In...[Details]
Guided wave radar level meter is a radar level meter based on the principle of time domain reflection (TDR). The electromagnetic pulse of the radar level meter propagates along the steel cable or pro...[Details]
Recently, Sunwanda stated in an institutional survey that the company has completed the development of 4C lithium iron phosphate batteries and will hold a product launch conference later; while the s...[Details]
What technology makes today's electronic health record applications intelligent? It's clinical decision support (CDS) systems. So now is the time to consider choosing a new CDS vendor.
Is it time...[Details]
(Note: Excerpted from the new book "Signal Integrity Measurement Technology".) As signal rates continue to increase and the requirements for accuracy become higher and higher, it is necessary to ...[Details]
It is easy to use LwIP, but to get good speed with LwIP, you can make the TCP network speed better by making the following modification to LwIP: lwipopts.h file /* TCP Maximum segment size. */ #defin...[Details]
The circuit shown in the figure below is a complete and highly integrated analog front-end industrial signal conditioner that uses a 16-bit differential input PulSAR ADC to digitally convert ±10 V ...[Details]
Working Principle of Stepper Motor
A stepper motor is a special type of motor that achieves rotational motion by gradually changing the direction and size of the electromagnetic field. It can ...[Details]
If "code" or "data" is not added before the array, the array is stored in the program memory by default;
code specifies that the data is stored in the code area. The data is written into the code mem...[Details]
As image clarity improves from standard definition to high definition, the cost of back-end storage devices has risen dramatically. Data shows that when using traditional DVR and NVR solutions, t...[Details]
According to Reuters, chip foundry TSMC said on June 1 that the company's new $12 billion chip factory has started construction in Phoenix, Arizona, USA. Phoenix officials approved financial incen...[Details]
ADC can be called the pearl in the field of analog chips.
As a key component, ADC design is difficult and has a high patent wall, so China has always been in a state of catching up.
I...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
