Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
TI 15.4-Stack is an IEEE 802.15.4e/g RF communication stack. It is an integral part of the SimpleLink CC13xx/CC26x2 Software Development Kit (SDK) and supports star topology networks for either Sub-1G...
Why is the current passing through rb'e in the high-frequency equivalent circuit of the transistor Ib? Shouldn't it be Ie? Which expert can answer this question? Thank you all....
[font=微软雅黑][color=#333333][font=微软雅黑][color=#444444]Recently, I have sorted out and collected some information about engineers using SD NAND on MCUs (mainly some mainstream STM32, Allwinner V3S and ot...
[i=s] This post was last edited by Baboerben on 2019-4-12 19:40 [/i] [size=4] Digital tubes are also one of the most commonly used output devices in single-chip microcomputer systems (along with liqui...
When downloading a program to the flash of the SM320F2812 chip, I found that the buttons on the On-Chip Flash Programmer interface are all gray, and only the Unlock button is lit and can be used. Howe...
I started playing board games 6 years after graduation.
It's been almost 9 years, and I don't have many boards.
Many lost their belongings when they graduated, worked or moved.
The rest are reluctant ...
Problems faced in the analysis of intended functional safety
At present, the industry mainly conducts the intended functional safety design test work in accordance with the process guidance of...[Details]
Friends who have used FriendlyArm know that the built-in interface design of FriendlyArm mini2440 is qt2, but now q4 is gradually becoming the mainstream. It is not easy to successfully transplant ...[Details]
At home, when it comes to hardcoreness, sweeping robots are no less capable than other high-tech products. Although many people think that sweeping robots are just vacuum cleaners with wheels that ...[Details]
Because of the output voltage fluctuation caused by the sudden change of load, when the fluctuation lasts longer than the switching cycle, it can be adjusted to a certain extent through feedback. T...[Details]
Weighing
sensor
is actually a device that converts mass signal into measurable electrical signal output. When using sensors, the actual working environment of the sensor must be considere...[Details]
1 Introduction
As energy and environmental issues are increasingly valued, electric vehicles are developing rapidly due to their clean and pollution-free, high energy efficiency, low noise, an...[Details]
I debugged the DMA working mode of USART6 yesterday, and I am posting this note today.
For the sake of brevity, the DMA of stm32 will not be introduced. If you don't know, you can search for it. Here...[Details]
On the morning of October 20, Google launched its own brand flagship mobile phone Pixel 6 series. The biggest feature of this phone is that it uses Google's self-developed chip Tensor. The price of...[Details]
According to Yonhap News Agency, Samsung Electronics' 2020 business report released on the 9th showed that the company's total equipment investment last year was 38.5 trillion won (about 220.6 billio...[Details]
A Power over Ethernet (PoE) solution
using ON Semiconductor's NCP1031 series of monolithic high voltage
switching
regulators with internal MOSFETs is described. This application note detail...[Details]
First, we need a new document. There are two ways to create this document (taking the delay1s function as an example). The first way is to create a delay1s.txt in the project directory and rename it t...[Details]
Hey everyone, I'm here to write another brake science post.
From Tesla, the market leader, to domestic new forces such as NIO and Xpeng; overseas brands such as Polestar 2 and Must...[Details]
Today I will tell you about the use of EEPROM. This memory uses IIC communication, so we need an IIC driver, or write one ourselves. I have written one before, so I will not write it here. Then I w...[Details]
On October 16, Shandong Yulong Gold Co., Ltd. (601028, hereinafter referred to as Yulong Co., Ltd. or the Company) issued an announcement that the company's industry was changed from wholesale to non-...[Details]
Wireless Connectivity
京公网安备 11010802033920号
EEWORLD
