Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
I am using bluetooth master module and CC2541 slave to connect.
Can the master module send data to the slave module?
If so, where is the TIperipheral routine that receives and processes the data?
I ca...
I often see people say that MOSFET is fully saturated and turned on. Can anyone provide a MOSFET that can be fully saturated and turned on?
Thinking is completely stuck in BJT. Using BJT to understand...
I made a multifunctional STM32 mini remote control in my spare time during the holiday. Because the PCB company was having a promotion, I could get the board for 5 yuan! After receiving the board, I o...
The AT32F421 is equipped with an RTC timer and is equipped with corresponding routines to assist in learning, use and functional verification.
The verification result of the routine ERTC_Calendar is s...
The working principle of this power supply can be analyzed with the help of Figure 2-4. When the switch tube T is turned on, the input voltage U of the power supply is added to the inductor L. The cu...[Details]
According to the author's observation, with the continuous saturation of the mobile phone industry in recent years, the terminal market has already begun to enter the stock competition market, and th...[Details]
There are four main reasons for interference to the microcontroller measurement and control system:
1. Grid interference
Most single-chip microcomputer control systems use AC ...[Details]
Changsha Industry and Information Technology Bureau allocated 60,000 yuan in bonuses to Hechu New Materials. Recently, Changsha Hechu New Materials Technology Co., Ltd.'s low-cost non-fluorine ion exc...[Details]
Wireless power supply is a convenient and safe new technology. It does not require any physical connection, and the electric energy can be transmitted to the load without contact at a close distanc...[Details]
At around 11 a.m. today (October 21), a fire suddenly broke out at TSMC's South Science Park in Tainan City, Taiwan Province. The construction sponge of the recycled water plant under construction ca...[Details]
South Korean media TheLec quoted UBI Research as saying that Samsung Electronics will launch three foldable smartphones next year. UBI said that Samsung Display is preparing three types of...[Details]
0 Preface Nowadays, in school dormitories, accidents such as students’ valuables being stolen and fires caused by students’ mistakes often occur. These are “big problems” that have been plaguing stud...[Details]
The research field of contemporary robots has moved from fixed-point operations in structured environments to autonomous operations in non-structured environments. The robot dexterous hand is equiv...[Details]
Following the hotel facility service robot and F&B (Food & Beverage) catering service robot, the third service robot developed by Hyundai Robotics - the "luggage robot" - is now on the market. ...[Details]
I won’t go into details about the IIC protocol here; Use analog IIC port definition B14 B15 #define AnalonSDA_Pin GPIO_PIN_12 #define AnalonSDA_GPIO_Port GPIOB #define AnalonSCL_Pin GPIO_PIN_13 #d...[Details]
1. How long is the life of a speaker? This is a question that many people are concerned about. Under normal use, it should be said that 15 years is absolutely no problem. If it is well maintained, ...[Details]
Hong Kong - Media OutReach - August 31, 2023 - Qingdao Innovation Qizhi Technology Group Co., Ltd. (hereinafter referred to as "Innovation Qizhi", together with its subsidiaries, collectively referre...[Details]
Silicon MEMS (Micro-electro-mechanical systems) crystals are becoming increasingly popular, mainly because designers need timing solutions with higher quality standards. Silicon MEMS crystals not onl...[Details]
Electric vehicles (EVs) are the future of mobility, but the biggest barriers to mass consumer adoption are range anxiety and price. While using a larger battery would be the obvious solution to inc...[Details]
Wireless Connectivity
京公网安备 11010802033920号
EEWORLD
