85/86 - 5/8 ” Square Single-Turn Panel Control with Rotary Switch
Potentiometer Specifications
Initial Electrical Characteristics
1
Conductive Plastic Element
Cermet Element
Standard Resistance Range
Linear Tapers (A, B, E, & H) ..................................................................(B & E) 1 K ohms to 1 megohm ............. (A & H) 100 ohms to 1 megohm
Audio Tapers (C, D, F, G, S, & T) .........................................................(D, G, S, & T) 1 K ohms to 1 megohm ... (C & F) 1 K ohms to 1 megohm
Total Resistance Tolerance .........................................................................±20 % or 10 % ...................................... ±10 % or 5 %
Absolute Minimum Resistance ...................................................................2 ohms maximum .................................. 2 ohms maximum
Operating Temperature Range ...................................................................-40 °C to +125 °C.................................. -40 °C to +125 °C
Storage Temperature Range ......................................................................-55 °C to +125 °C.................................. -55 °C to +125 °C
Temperature Coefficient Over Storage Temperature Range ......................±1,000 ppm/°C ...................................... ±150 ppm/°C
Vibration (Single Section) ...........................................................................15 G ....................................................... 15 G
Total Resistance Shift ...........................................................................±2 % maximum ..................................... ±2 % maximum
Voltage Ratio Shift ................................................................................±5 % maximum ..................................... ±5 % maximum
Shock (Single Section) ...............................................................................30 G ....................................................... 30 G
Total Resistance Shift ...........................................................................±2 % maximum ..................................... ±2 % maximum
Voltage Ratio Shift ................................................................................±5 % maximum ..................................... ±5 % maximum
Total Resistance Shift ...........................................................................±10 % maximum ................................... ±5 % maximum
Rotational Life (No Load) ............................................................................100,000 cycles ...................................... 100,000 cycles
Total Resistance Shift ...........................................................................(Linear taper) 10 ohms or ..................... (All tapers) ±5 % TRS maximum
Moisture Resistance (MIL-STD-202, Method 103, Condition B)
Total Resistance Shift ...........................................................................(B & E tapers) ±10 % maximum ........... ±5 % maximum (all tapers)
IP Rating .....................................................................................................IP 40 ...................................................... IP 40
Starting and Running Torque (Non-Locking Bushings)
Single Section ................................................................................................................................................................. 0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)
Dual Section .................................................................................................................................................................... 0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)
Triple Section ................................................................................................................................................................... 0.35 to 1.41 N-cm (0.5 to 2.0 oz.-in.)
Quadruple Section .......................................................................................................................................................... 0.35 to 1.41 N-cm (0.5 to 2.0 oz.-in.)
Starting and Running Torque (Locking Bushings) ..................................................................................................... 0.14 to 2.82 N-cm (0.2 to 4.0 oz.-in.)
Shaft Locking Torque with Locknut @ 10 in-lb. (B & E Bushings) ........................................................................................................ 14 N-cm (20 oz-in.)
Mounting ...................................................................................................................................................................1.7-2.0 N-m (15-18 lb.-in.) maximum
Weight (Single Section).............................................................................................................................................................................. 21 grams maximum
(Each Additional Section) ...................................................................................................................................................................... 6 grams maximum
Terminals .......................................................................................................................................................................... Printed circuit terminals or J-Hooks
Soldering Condition .................................................................. Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ” wire diameter.
Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean flux.
Marking.......................................................................... Manufacturer’s trademark, wiring diagram, date code and resistance, manufacturer’s part number
Ganging (multiple section potentiometers) ..................................................................................................................................................... 4 cup maximum
Hardware ...........................................One lockwasher and one mounting nut is shipped with each potentiometer, except where noted in the part number.
For dimensional drawings see pages 3 & 4.
For ordering information see page 5.
NOTE: Model 81/82 performance specifications do not apply to units subjected to printed circuit board cleaning procedures.
1At room ambient: +25 °C nominal and 50 % relative humidity nominal, except as noted.
*RoHS Directive 2002/95/EC Jan 27, 2003 including Annex.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications
81/82 - 5/8 ” Square Single-Turn Panel Control
85/86 - 5/8 ” Square Single-Turn Panel Control with Rotary Switch
Rotary Switch Specifications
Initial Electrical Characteristics
1
Contacts:
DPST ...............................................................................................................................................................................N.O/N.O.,N.C./N.C. or N.O./N.C.
DPDT ................................................................................................................................................................................2 N.O./N.C. (break before make)
Power Rating (Resistive Load):
DPST ............................................................................................................ 2 A @ 125 volts RMS-60 Hz or 2 A @ 28 VDC, 1 A @ 250 volts RMS-60 Hz
DPDT ........................................................................................................................................................... 1 A @ 125 volts RMS-60 Hz or 1 A @ 28 VDC
Operating Temperature Range ...........................................................................................................................................................................0 °C to +70 °C
Storage Temperature Range ........................................................................................................................................................................ -65 °C to +125 °C
Vibration (Dual Section) ....................................................................................................................................................................................................... 8 G
(Triple Section) .................................................................................................................................................................................................... 5 G
(Quadruple Section) ........................................................................................................................................................................................... 3 G
Contact Resistance ........................................................................................................................................................................ 10 milliohms maximum
Contact Bounce ......................................................................................................................................................................... 0.1 millisecond maximum
Shock (Dual Section) ......................................................................................................................................................................................................... 20 G
(Triple Section) ...................................................................................................................................................................................................... 15 G
(Quadruple Section) ............................................................................................................................................................................................. 10 G
Contact Resistance ........................................................................................................................................................................ 10 milliohms maximum
Contact Bounce ......................................................................................................................................................................... 0.1 millisecond maximum
Rotational Life ..................................................................................................................................................................................................... 25,000 cycles
Switch Actuating Torque (50% Duty cycle @ Rated Power Load) .................................................................................. 1.41 to 4.94 N-cm (2 to 7 oz.-in.)
Contact Resistance ...................................................................................................................................................................... 100 milliohms maximum
Moisture Resistance (MIL-STD-202, Method 106, Condition B)
Contact Resistance (0.1 VDC-10 mA) ............................................................................................................................................ 10 milliohms maximum
Switch Housing Material ................................................................................................................. High temperature, flame retardant, thermosetting plastic
Mechanical Characteristics
1
Actuating Torque (Each Section, Switch Module Only) ....................................................................................................... 3.53 to 10.6 N-cm (5 to 15 oz.-in.)
Running Torque (Out of Detent, 2-4 Module Assembly)..................................................................................................... 0.21 to 1.41 N-cm (0.3 to 2 oz.-in.)
Detent ..................................................................................................................................................................................................... CW or CCW standard
Contact Materials ..........................................................................................................................................................................Fine silver with gold overlay
Terminal Styles .................................................................................................................................................................................................. Solder lug only
Standard Orientation ..............................................................................................................................................................In-line with control terminals
Optional .......................................................................................................................................................................... Rotated 90 ° CCW from standard
Terminal Strength (Before and After Soldering Heat Exposure) .......................................................................................................... 0.9 Kg (2 lbs.) minimum
NOTE: Model 81/82 performance specifications do not apply to units subjected to printed circuit board cleaning procedures.
1At room ambient: +25 °C nominal and 50 % relative humidity nominal, except as noted.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications
This course is aimed at MSP430 MCU beginners. It introduces how to develop MSP430 projects from scratch, including an introduction to MSP430 MCU products and typical applications, how to obtain develo...
Where exactly does the output power of an external MOS like a DCDC chip limit? For example, if I get a chip, how can I consider its maximum output power?...
The signal generator can emit signals of various waveforms, including common sine, square, pulse, Gaussian, etc., uncommon cardiac waveforms, pulse waveforms, various customized waveforms, etc., as sh...
The process of electronic hardware design includes hardware requirements, schematic design, PCB design, PCB manufacturing, UT and integrated testing, etc. Among them, in the PCB board processing and m...
MSP430F20x1, MSP430F20x2, MSP430F20x3 Mixed Signal Microcontroller Datasheet
DescriptionThe Texas Instruments (TI) MSP430 family of ultra-low-power microcontrollers consists of multiple devices with d...
This article is based on the dual-tube forward low-power power supply of the TL494 driver chip. Let's first talk about the forward conversion. The forward conversion has a simple topology and a wide...[Details]
Preface: The teaching and research department is doing DSO, so first get familiar with the basics About the bandwidth of digital oscilloscopes Bandwidth - the first indicator of an oscilloscope and a...[Details]
Researchers have discovered a collision attack vulnerability in iOS's built-in hashing algorithm, raising new concerns about Apple's CSAM scanning system, but Apple said the discovery does not ...[Details]
On June 7, the General Administration of Customs data showed that in the first five months of this year, imports of mechanical and electrical products amounted to 2.87 trillion yuan, an increase of ...[Details]
More environmentally friendly and energy-saving: Next-generation systems powered by NVIDIA point to the future development direction of data centers Although Moore's Law has ended, the need to impr...[Details]
This article introduces the development process of DCT based on the development process of SAIC dual-clutch transmission (DCT).
1 Design and development of DCT
In the early stage of...[Details]
The inverter and servo motor on the extrusion coating machine can be connected to the PLC through the Xingda Easy Control Modbus conversion Profinet gateway for real-time communication and adjust t...[Details]
First, dot matrix: (take the simplest 8X8 as an example, 16X16 will be discussed later) 8X8 dot matrix Personally, I feel that there are some things that need to be paid attention to in the d...[Details]
The design of magnetic components is an important part of the switching power supply. Since the planar transformer has great advantages in improving the characteristics of the switching power suppl...[Details]
introduction
Traditionally, the automatic water regime monitoring and reporting system in the northern high-altitude cold regions must be dismantled in winter and then reinstalled in the s...[Details]
This paper introduces the design concept and hardware circuit of the image recognition
system
based on SPCA563B chip in detail
, and gives specific application examples. The image data co...[Details]
Before writing the linker script for GNU ARM assembly, it is necessary to look at the ldr instruction, as well as the ldr and adr pseudo-instructions.
ldr instruction:
LDR lo...[Details]
What matters need to be paid attention to when wiring the turbine flowmeter? Zhirui will explain to you. 1. The wiring position of the turbine flowmeter should be as far away from the electrical nois...[Details]
Abstract: A high-precision digital waveform generator for virtual instruments. The polyline approximation method and the triangular decomposition implementation method are adopted, and the hardw...[Details]
1. Introduction
With the development of online video platforms, users' demand for 4K high-definition quality is growing. However, many users have found that even if they have purchased m...[Details]
TI Technology Forum
京公网安备 11010802033920号
EEWORLD
