Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
What are the options for isolated DAC/ADC? APCPAC chips
Analog signal isolation is a commonly used technology in electric vehicles, industrial control, PLC, motor drive, power supply, inverter and oth...
Share this article to briefly analyze the differences and trade-offs between STM32 and 51 microcontrollers.A single-chip microcomputer is abbreviated as an MCU. In simple terms, it is a device that in...
A senior project used a digital tube, a three-pin inductor, and a three-pin capacitor.1. Are common anodes or common cathodes more commonly used in digital tubes?2. The difference between a three-pin ...
[color=#000000][backcolor=white]In the book (The Art of Electronics), I saw "If the residual drift of the integrator is still too large for a given application, it may be necessary to put a large resi...
introduction
The original meaning of MOSFET is: MOS (Metal Oxide Semiconductor), FET (Field Effect Transistor), that is, a field effect transistor that uses the gate of the metal layer (M) to control ...
Last day! Free review of Beetle ESP32-C3, hurry up and get it!Evaluation Development Board IntroductionBeetle ESP32-C3 (RISC-V chip)Small-sized controller based on ESP32-C3, with integrated charging m...
The unique low voltage and micro power consumption characteristics of liquid crystal display devices enable them to be directly combined with large-scale integrated circuits to develop a series of ...[Details]
Semiconductor silicon wafers are one of the links where the gap between my country's semiconductor industry chain and the international advanced level is the largest. In addition, the supply concentr...[Details]
During the mortar live-fire shooting, it is common for mortar shells to misfire. If a mortar shell does not fire, it is strictly forbidden to reload the shell. If reloading, it is easy to cause a cha...[Details]
At present, switching power supply technology has been fully integrated into the design of various electronic products. However, with the expansion of its use, switching power supplies are beginn...[Details]
Keithley source meters and multimeters have always been favored by customers. During use, people often ask: What is the four-wire test method? Today, Antai Test will simply share with you what the fo...[Details]
Scientists at the University of Pennsylvania have developed a memory device that can work continuously for 60 hours at 600°C. This temperature tolerance is more than twice that of current commercia...[Details]
Honor Mobile officially released a pre-heating video for the Honor X30. The video shows that the Honor X30 inherits the classic ring-shaped rear lens module design, which is full of nostalgia. From...[Details]
0 Introduction
As a new type of dynamic monitoring technology, acoustic emission technology occupies an important position in non-destructive testing technology. Non-destructive testing technol...[Details]
The emergence of the emerging field of
semiconductor lighting
has made engineers who specialize in
power electronics
,
optics
, and thermal management (mechanical enginee...[Details]
Key points: The third-generation Snapdragon 7+ mobile platform introduces many terminal-side generative AI functions to the Snapdragon 7 series for the first time, while improving CPU perform...[Details]
Preface
Laser displacement sensors can use the high directivity, high monochromaticity and high brightness of lasers to achieve non-contact long-distance measurement. Laser displacement sensors (ma...[Details]
Without considering EL2 and EL3, IRQ processing is divided into two cases: interrupts occurring in user mode and interrupts occurring in kernel mode. The corresponding interrupt processing interfaces...[Details]
As the forward current of high brightness LEDs increases and package size decreases, the potential for thermal runaway and catastrophic failure also increases. In many LED applications, higher lev...[Details]
The linear frequency modulation signal has a parabolic nonlinear phase spectrum and can obtain a larger time-bandwidth product. Compared with other pulse compression signals, it is easy to generate...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
