EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

BF030-26C-B0-0400-0277-0600-LD

Description
Board Connector, 26 Contact(s), 2 Row(s), Male, Straight, 0.079 inch Pitch, Surface Mount Terminal, Black Insulator,
CategoryThe connector    The connector   
File Size94KB,1 Pages
ManufacturerGlobal Connector Technology
Environmental Compliance
Download Datasheet Parametric View All

BF030-26C-B0-0400-0277-0600-LD Overview

Board Connector, 26 Contact(s), 2 Row(s), Male, Straight, 0.079 inch Pitch, Surface Mount Terminal, Black Insulator,

BF030-26C-B0-0400-0277-0600-LD Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid314415007
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.157 inch
subject depth0.109 inch
body length1.031 inch
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN ON NI
Contact completed and terminatedTin (Sn) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialCOPPER ALLOY
contact modeRECTANGULAR
Contact resistance20 mΩ
Contact styleSQ PIN-SKT
Dielectric withstand voltage500VAC V
Durability100 Cycles
maximum insertion force2.0016 N
Insulation resistance1000000000 Ω
Insulator colorBLACK
insulator materialLIQUID CRYSTAL POLYMER (LCP)
JESD-609 codee3
Manufacturer's serial numberBF030
Plug contact pitch0.079 inch
Match contact row spacing0.079 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
PCB contact patternRECTANGULAR
PCB contact row spacing3.7592 mm
Rated current (signal)2 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal pitch2.0066 mm
Termination typeSURFACE MOUNT
Total number of contacts26
Evacuation force-minimum value.199882 N
I'm a newbie and need help. How to declare lcd_wdat? Please help me.
I am a newbie with a poor foundation in MCU C language. I saw a compilation error in a case program in a book. If I am not wrong, is it a declaration problem? So how should lcd_wdat be declared, what ...
落魄IV MCU
Experience in Application Test of DSP External SRAM
Figure 1-1 Code Composer Studio 6.0.0.00190 C/C++ development environment The hardware platform is based on the TMS320F28335 chip, and the software platform is based on TI's Code Composer Studio 6.0.0...
fish001 Microcontroller MCU
【TI mmWave Radar Evaluation】+Configuration File Test (Part 2)
Continuing from the previous post: adcbufCfg 0 1 0 1 //ADC cache configuration The document describes that the first parameter configuration is 0, does not support IWR144, only supports 16, the second...
29447945 TI Technology Forum
[AT-START-F425 Review] + Get MCU 96-bit unique ID, FLASH size
1. About electronic signature The electronic signature of the device contains storage capacity information and a 96-bit unique device ID. It is stored in the information module of the on-chip flash me...
freeelectron Domestic Chip Exchange
Looking for a car charger IC with dual port output power of 40W or more C+A port
Looking for a car charger IC with dual-port output power of more than 40W. The C+A port requires various charging protocols, at least PD protocol, and can support MAC BOOK charging. Please recommend i...
fangfang120 Power technology
Why does the ripple of a switching power supply increase as the output voltage decreases?
[i=s]This post was last edited by sfcsdc on 2020-4-20 16:35[/i]Previously I asked you how a switching power supply can output a voltage lower than the reference voltage. https://en.eeworld.com/bbs/thr...
sfcsdc Analog electronics

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号