EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

7205P1D9V2GE2

Description
TOGGLE SWITCH,STRAIGHT,DPDT,(ON)-OFF-(ON),PC TAIL TERMINAL,TOGGLE,10
CategoryMechanical and electronic products    switch   
File Size1MB,14 Pages
ManufacturerC&K Components
Environmental Compliance
Download Datasheet Parametric View All

7205P1D9V2GE2 Overview

TOGGLE SWITCH,STRAIGHT,DPDT,(ON)-OFF-(ON),PC TAIL TERMINAL,TOGGLE,10

7205P1D9V2GE2 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid310545714
Reach Compliance Codenot_compliant
ECCN codeEAR99
Actuator angle25 deg
Actuator colorBLACK
Actuator length0.84 inch
Actuator materialBRASS
Actuator typeTOGGLE
body width11.43 mm
body height14.097 mm
Body length or diameter19.05 mm
Nozzle length0.35 inch
Casing type1/4-40
center contact materialCOPPER ALLOY
Center contact platingGOLD OVER NICKEL
Contact (AC) maximum rated R load2A@250VAC
Maximum contact current (AC)2 A
Maximum contact current (DC)5 A
Contact (DC) maximum rated power R load0.4VA@20VDC
Contact (DC) maximum rated R load5A@28VDC
Contact function(ON)-OFF-(ON)
Contact resistance0.01 mΩ
Maximum contact voltage (AC)250 V
Maximum contact voltage (DC)28 V
Dielectric withstand voltage1400VAC V
Electrical life100000 Cycle(s)
End contact materialCOIN SILVER
End contact platingGOLD OVER NICKEL
Shell materialSTAINLESS STEEL
Insulation resistance1000000000 Ω
JESD-609 codee4
Manufacturer's serial number7000
Installation featuresTHROUGH HOLE-STRAIGHT
Maximum operating temperature85 °C
Minimum operating temperature-30 °C
PCB hole count10
sealEPOXY
SolderabilityMIL-STD
surface mountNO
switch functionDPDT
Switch typeTOGGLE SWITCH
Terminal surfaceGold (Au) - with Nickel (Ni) barrier
Terminal materialCOPPER ALLOY
Termination typeSOLDER
Development of C-band Programmable Phase Shifter
Programmable phase shifters are widely used in microwave systems, especially in missile simulation systems. Their accuracy and delay are directly related to the simulation results of the entire missil...
JasonYoo Analog electronics
[GD32L233C-START Review] 8. Comprehensive Application of Kitchen Countdown Timer
[i=s]This post was last edited by lising on 2022-4-11 10:21[/i]This comprehensive experiment uses the GD32L233C-START development board to make a kitchen countdown timer with a timing range of 1 (min)...
lising GD32 MCU
Has anyone successfully mounted a USB flash drive with GD32+FATFS? Please advise
The current STM32105+FATFS 0.13C can be mounted on a USB flash drive normally.The code remains unchanged, only the STM32 on the board is replaced with GD32F105, and the USB flash drive cannot be mount...
mini_peng GD32 MCU
【i.MX6ULL】Driver Development 1——Character Device Development Template
The previous articles (starting from i.MX6ULL Embedded Linux Development 1-Preliminary Exploration of Uboot Transplantation ) introduced the system transplantation of embedded Linux (Uboot, kernel and...
DDZZ669 ARM Technology
What are the components FB1 and FB2 on the lpc824 DIP development board?
Recently I took a look at the information of the lpc824 DIP development board and found that there are two components FB1 and FB2 on the board, which are used to connect AGND and DGND. The schematic s...
bigbat NXP MCU
Can signaltap be set to automatically trigger after power-on? I encounter abnormal counting after power-on.
The debug script reads out that a register is 1 after power-on. This section of code is generated by a for loop. The initial values of the other registers are normal and there is no problem with the t...
qan FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号