Lead Temperature (soldering, 5 seconds) ................................. 260°C
Storage Temperature Range ..................................... -65°C to +150°C
Operating Junction Temperature Range ................... -40°C to +125°C
Input Voltage (Note 5) ................................................................... 16V
ELECTRICAL CHARACTERISTICS
At V
IN
=V
OUT
+ 1V and I
OUT
= 10 mA, C
IN
= 6.8
µF,
C
OUT
= 10µF; T
A
= 25°C, unless otherwise specified.
The Boldface applies over the junction temperature range. Adjustable versions are set at 5.0V.
PARAMETER
1.8V Version
Output Voltage
2.5V Version
Output Voltage
3.3V Version
Output Voltage
5.0V Version
Output Voltage
All Voltage Options
Line Regulation
Load Regulation
∆V
∆T
Dropout Voltage (Note 1)
(except 1.8V version)
Ground Current (Note 3)
I
GNDDO
Ground Pin
Current at Dropout
Current Limit
Output Noise Voltage
(10Hz to 100kHz)
I
L
=100mA
Thermal Resistance
I
O
=10mA, (V
OUT
+1V)≤V
IN
≤16V
V
IN
=V
OUT
+1V, 10mA≤I
OUT
≤1A
Output Voltage
Temperature Coef.
I
O
=100mA
I
O
=1A
I
O
=750mA, V
IN
=V
OUT
, + 1V
I
O
=1A
V
IN
=0.1V less than specified V
OUT
I
OUT
= 10mA
V
OUT
=0V (Note 2)
C
L
= 10µF
C
L
=33µF
TO-220 Junction to Case, at Tab
TO-220 Junction to Ambient
TO-263 Junction to Case, at Tab
TO-263 Junction to Ambient
SOT-223 Junction to Case, at Tab
SOT-223 Junction to Ambient
0.2
0.3
20
70
280
12
18
1.2
2.2
400
260
3
29.4
3
31.4
15
62.3
°C/W
°C/W
°C/W
1.5
1.5
1.0
1.5
100
200
550
25
1.0
1.5
100
200
550
25
mA
mA
A
µV
RMS
%
%
ppm/°C
mV
I
OUT
= 10mA
10mA≤I
OUT
≤1A,
6V≤V
IN
≤16V
5.0
5.0
4.950
4.875
5.050
5.125
4.900
4.825
5.100
5.175
V
I
OUT
= 10mA
10mA≤I
OUT
≤1A,
6V≤V
IN
≤16V
3.3
3.3
3.267
3.217
3.333
3.383
3.234
3.184
3.366
3.416
V
I
OUT
= 10mA
10mA≤I
OUT
≤1A,
6V≤V
IN
≤16V
2.5
2.5
2.475
2.437
2.525
2.563
2.450
2.412
2.550
2.588
V
I
OUT
= 10mA
10mA≤I
OUT
≤1A,
6V≤V
IN
≤16V
1.8
1.8
1.782
1.755
1.818
1.845
1.764
1.737
1.836
1.863
V
CONDITIONS
TYP
MIN
MAX
SPX3940A (1%)
MIN
MAX
SP3940 (2%)
UNITS
NOTES:
Note 1: Dropout voltage is defined as the input to output differential when the output voltage drops to 99% of its normal value.
Note 2: V
IN
=V
OUT (NOMINAL)
+ 1V. For example, use V
IN
=4.3V for a 3.3V regulator. Employ pulse-testing procedures to minimize temperature rise.
Note 3: Ground pin current is the regulator quiescent current. The total current drawn from the source is the sum of the load current to the ground current.
Note 4: Thermal regulation is defined as the change in the output voltage at a time T after a change in power dissipation is applied, excluding load or line regulation effects.
Note 5: Maximum positive supply voltage of 20V must be of limited duration (<100ms) and duty cycle (<1%). The maximum continuous supply voltage is 16V.
The kernel driver can not only compile the driver into the kernel, but also dynamically compile the kernel driver. This document describes how tocompile the kernel driver in a module way.To compile th...
When learning DSP development, I often feel that there are too many technical documents. Every book is useful and I want to read every book, but I don't know where to start. At this time, the principl...
[i=s]This post was last edited by wuguangtao on 2020-11-27 21:41[/i] # MSP430F5529 drives WS2812B LED Last time I used MAX7219 to drive a monochrome LED dot matrix screen. This time I changed to a coo...
1. S parameters depend on system impedance
Accurate power measurement is the most basic requirement in RF and microwave wireless systems. There are many measurement equipment and test methods to choos...
Embedded System
京公网安备 11010802033920号
EEWORLD
