The properly and electrostatically measured taping materials are used for the components, but attention should be paid to the fact that there is some danger the parts absorb on the top
tapes to cause a failure in the mounting and the parts are destructed by static electricity (more than 1kV : 1J, 2A, 2B, 2E 0.5kV : 1E, Human Body Model 100pF 1.5kΩ) to change the
resistance in the conditions of an excessive dryness or after the parts are given vibration for a long time as they are packaged on the tapes. Similarly, care should be given not to apply the
excessive static electricity when mounting on the boards.
●
Ionic impurities such as flux etc. that are attached to these products or those mounted onto a PCB, negatively affect their moisture resistance, corrosion resistance, etc. The flux may
contain ionic substances like chlorine, acid, etc. while perspiration and saliva include ionic impurities like sodium (Na
＋
), chrorine (Cl
−
) etc. Therefore these kinds of ionic substances may
induce electrical corrosion when they invade into the products. Either thorough washing or using RMA solder and flux are necessary since lead free solder contains ionic substances.
Washing process is needed, before putting on moisture proof material in order to prevent electrical corrosion.
●
Please pay attention that the top of an iron does not direct touch to the components. There is a risk that may cause a change in resistance. Take care that another risk may happen that
the protecting coat is carbonized in an instant when touched directly by the top of the iron, also climatic-proof for electric corrosion or insulation of protecting coat may be dropped down.
Be sure not to give high temperature on the top of the iron as it will degrade the protecting coat.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling strength. 5∼
35℃/35∼75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas like hydrogen sulfide, sulfurous acid
gas, hydrogen chloride, etc. may drop solderability.
There are two basic sections in the CMD file: the initialization section and the non-initialization section. The initialization section contains codes and constants that must be valid after the DSP is...
These days I have seen many students who don’t know how to learn 51 single-chip microcomputers. It is not difficult to learn single-chip microcomputers well. Single-chip microcomputers are a very prac...
Using timer interrupt to realize variable frequency flashing of LED lightsThe example is relatively simple, and the source code is directly posted.
#include "DSP2833x_Device.h" // DSP2833x Headerfile ...
Using STM32F103VET6 microcontroller, DAC+DMA+TIM2 trigger mode, channel 1 outputs sine wave, refer to the routine configuration, but there is no signal output, the hardware is checked and it is normal...
[i=s]This post was last edited by yjtyjt on 2019-9-17 20:36[/i]Showing off the Jingdong E-card exchanged with E-coins. I liked some of the coins and exchanged them for a 400 yuan E-card on Jingdong. W...
[i=s]This post was last edited by elec32156 on 2020-4-19 16:33[/i]The figure shows 74HC165 shift registers, which are connected in series. One is 8 bits, and two can achieve 16-bit data output (ultima...
Domestic cars
Chips
The third round.
New energy vehicles are powerful, and one of the important chips behind them is
the
battery
management chip.
Battery mana...[Details]
I encountered many problems when transplanting fatfs, which was very distressing. The transplantation was not easy, so I would like to share my experience. The hardware is STM32F103RBT6, which has onl...[Details]
This article introduces the five main factors that affect resistance or resistivity testing, including: ambient temperature and humidity, test voltage (electric field strength), test time, leakage of ...[Details]
There are certain differences between ordinary motors and variable frequency motors in terms of working principles, structures, and applicable occasions. Therefore, ordinary motors cannot be used d...[Details]
OFweek Cup · OFweek 2023 China
Robot
Industry Annual Selection (abbreviated as OFweek Robot Awards 2023) is jointly organized by OFweek, China's high-tech industry portal, and its authorita...[Details]
The standard orifice flowmeter for flow measurement has a long history and is widely used. It is characterized by simple structure, long service life and wide adaptability. At present, the structur...[Details]
1 Working principle of full-bridge transformer switching power supply The working principle of the full-bridge transformer switching power supply is very similar to that of the push-pull transfor...[Details]
There are two ways to express the basic error. For DC and AC voltage blocks and current blocks, it is expressed as a percentage of the upper limit of the working part of the scale. The scales of thes...[Details]
With the rapid growth of the electric vehicle (EV) market and the continuous advancement of technology, the importance of the battery management system (BMS) as the core component of electric vehic...[Details]
Ease of use is an essential quality and belongs to the bottom line of blind-filling lidar. In addition to being easy to use, blind-filling lidar also has a more intuitive competitiveness, and that...[Details]
The chip manufacturing process is a long chain, and many important process links require precise detection methods to detect defects, ensure yield, reduce production costs, and improve control proces...[Details]
Film capacitors are also called plastic film capacitors. They use plastic film as dielectric. There are many types of capacitors depending on the dielectric, such as electrolyte capacitors, paper cap...[Details]
There are three main applications of electromagnetic flowmeters in various industries: * Large-caliber instruments are mostly used in water supply and drainage projects; Second, small and medium ca...[Details]
introduction We live in a colorful analog world, and with the rapid development of digitalization today, it is particularly important to convert analog signals into digital fields, which requires d...[Details]
Electric cars are the future of sustainable transportation. They have large battery compartments on wheels and are an alternative to gas-guzzling, carbon-intensive internal combustion engines.
...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
