EEWORLDEEWORLDEEWORLD

Part Number

Search

WBA-T0303GG-07-3831-BB

Description
RES NET,THIN FILM,3.83K OHMS,100WV,.1% +/-TOL,-25,25PPM TC,0303 CASE
CategoryPassive components    The resistor   
File Size484KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

WBA-T0303GG-07-3831-BB Overview

RES NET,THIN FILM,3.83K OHMS,100WV,.1% +/-TOL,-25,25PPM TC,0303 CASE

WBA-T0303GG-07-3831-BB Parametric

Parameter NameAttribute value
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Manufacturer's serial numberWBA
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
GuidelineMIL-PRF-38534
resistance3830 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesWBA
size code0303
Temperature Coefficient-25,25 ppm/°C
Tolerance0.1%
Operating Voltage100 V
Wire Bondable
Ceramic Resistors
WBA Series
High resistor density
Lower stray capacitance
Proven TaNFilm
®
on ceramic technology
IRC’s WBA series wire bondable ceramic resistors are ideally suited for
your most demanding hybrid application. IRC’s TaNFilm
®
tantalum nitride
thin film technology has years of proven stability, reliability and moisture performance.
IRC’s WBA series of ceramic chip resistors offer a wide range of tolerances and temperature coefficients to fit
a variety of hybrid circuit applications. Custom resistance values, sizes and schematics are also available on
request to the factory.
For high performance wire bondable ceramic resistors for hybrid circuit application, specify IRC WBA series
resistors.
Electrical Data
Absolute Tolerance
Ratio Tolerance
Absolute TCR
Tracking TCR
Package Power Rating (@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Noise
Substrate Material
Substrate Thickness
Bond Pad Metallization
Backside
to ±0.1%
to ±0.05%
to ±25ppm/°C
to ±2ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
99.6% Alumina
0.015˝ ±0.002
(0.381mm ±0.05)
Gold: 30KÅ minimum
Ceramic (gold available)
Physical Data
T0303 - Tapped network
(0.762mm ±0.025)
0.004˝ min
Bond Pads
A subsidiary of
TT electronics plc
0.030˝ ±0.001
(0.762mm ±0.025)
½R
½R
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
WBA Series Issue January 2009 Sheet 1 of 3
0.030˝ ±0.001
[Domestic RISC-V Linux board Fang·Starlight VisionFive trial report] C language programming to control WS2812B colorful lamp beads
The RISC-V single-board computer used in this trial provides us with 40 pin interfaces, including the SPI interface. WhatI want to share today is how to use SPI to drive the ws2812B colorful lamp bead...
HonestQiao Domestic Chip Exchange
The AD voltage check has been completed, how to connect it to the LED
1. Battery voltage detection . 2. Voltage displayed on LCD1602 3. When the voltage is lower than 2.6V, the indicator light flashes. 4. When the voltage is higher than 3.3V, the indicator light flashes...
新晋电子发廋友 51mcu
Mechanical and electrical system testing and control from entry to mastery
"Electromechanical System Testing and Control from Entry to Mastery" is aimed at the professional knowledge background of undergraduate graduates majoring in electromechanical engineering. First, in t...
arui1999 Download Centre
I would like to ask a question about LCD power supply circuit.
The picture shows an LCD power supply circuit. Boosting 5V to 9.6V is a normal boost circuit. I would like to ask about the generation principle of +18V and -7.5V....
Kkk- Power technology
Tektronix TDS7254 Oscilloscope Trigger Failure Repair Case
An example of troubleshooting a trigger failure on a Tektronix TDS7254 oscilloscope1. Instrument model:Tektronix oscilloscope TDS72542. Fault phenomenon:The customer reported that after the oscillosco...
agitek2019 Integrated technical exchanges
DSP28335 ADC software trigger
I want to sample at the start and end of the effective vector of svpwm. The method I have thought of now is to use the ADC's s/w software trigger, but I don't know how to use the software trigger. How...
wangzhaohui01 DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号