IP Rating ............................................................ IP 40 .....................................................................IP 40
*RoHS Directive 2002/95/EC Jan 27 2003 including Annex
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
Model 91, 92, 93, 94 & 95 - 5/8 ” Square Single-Turn Panel Control
Mechanical Characteristics
1
Stop Strength (1/4 ” D shaft) .............................................................................................................................................45.19 N-cm (4 lb.-in.)
(1/8 ” D shaft) .............................................................................................................................................33.89 N-cm (3 lb.-in.)
Starting ........................................................................................................................................... 0.3 max. above average running torque
Running Torque
Single or Dual Section (A & R Bushings) .................................................................................................. 0.21 to 1.06 N-cm (0.3 to 1.5 oz.-in.)
Single or Dual Section (C & U Bushings) .................................................................................................. 0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)
Mounting .............................................................................................................................................1.7-2.0 N-m (15-18 lb.-in.) maximum
Variation ...................................................................................................................... 0.35 N-cm (0.5 oz.-in.) maximum in 45 ° shaft travel
Weight (Single Section, Metal Bushing)...............................................................................................................................12.7 grams nominal
Terminals .................................................................................................................................Printed circuit terminals, J-Hooks or solder lugs
Soldering Condition ...........................................Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ” wire diameter.
Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean flux.
Marking ..................................................................................Manufacturer’s trademark, date code, resistance, manufacturer’s part number
Ganging (Multiple Section Potentiometers).............................................................................................................................2 cups maximum
Hardware ...................One lockwasher and one mounting nut is shipped with each potentiometer, except where noted in the part number.
NOTE:
1
At
Performance specifications do not apply to units subjected to printed circuit board cleaning procedures.
room ambient: +25 °C nominal and 50 % relative humidity nominal, except as noted.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
Model 91, 92, 93, 94 & 95 - 5/8 ” Square Single-Turn Panel Control
Product Dimensions
Model 91 PC Pin Terminals, In-Line
22.86 ± 0.43
(.900 ± .017)
MOUNTING
SURFACE
12.70 ± .229
(.500 ± .009)
0.79 ± .025
(.031 ± .010)
DIA.
13.72 ± 0.38
(.540 ± .015)
1.37 ± 0.08
(.054 ± .003)
2.36 ± 0.08
(.093 ± .003)
15.88
(.625)
7.92
(.312)
Model 92 J-Hooked
Terminals, In-Line
.79
(.031) 2 PLCS.
3 2 1
SEE
HOW TO ORDER
CHART FOR
BUSHING OPTIONS.
10.16 ± 0.30
(.400 ± .012)
11.05 ± 0.20
(.435 ± .008)
SEE
NEXT PAGE
FOR SHAFT
OPTIONS.
2.54
(.100)
2.54
(.100)
1.19
(.047)
“A” STYLE
A.R. LUG
R
9.53
(.375)
15.29 ± 0.56
(.602 ± .022)
.254
(.010)
GAP
5.08
(.20)
1.52
(.06)
R2
R1
1
2
3
1
2
3
0.76 ± 0.05
(.030 ± .002)
TYP.
Model 94 J-Hooked
Terminals, "L" Pattern
Model 93 PC Pin Terminals, "L" Pattern
22.86 ± 0.43
(.900 ± .017)
MOUNTING
SURFACE
12.70 ± .229
(.500 ± .009)
0.79 ± .025
(.031 ± .010)
DIA.
13.72 ± 0.38
(.540 ± .015)
1.37 ± 0.08
(.054 ± .003)
2.36 ± 0.08
(.093 ± .003)
15.88
(.625)
7.92
(.312)
.81
(.032)
R. MAX.
5.33 ± .76
(.21 ± .03)
3.81
(.150)
MAX. TYP.
1.52
(.06)
GAP
3 2 1
SEE
HOW TO ORDER
CHART FOR
BUSHING OPTIONS.
DIA.
0.81
TYP.
(.032)
10.16 ± 0.30
(.400 ± .012)
R2
R1
5.08 ± 0.38
(.200 ± .015)
11.05 ± 0.20
(.435 ± .008)
SEE
NEXT PAGE
FOR SHAFT
OPTIONS.
1.19
(.047)
“A” STYLE
A.R. LUG
R
9.53
(.375)
12.70 ± 1.02
(.500 ± .040)
Shaft Flat Orientation
2.54
(.100)
2.54
(.100)
1
3
2
1
3
2
0.76 ± 0.05
(.030 ± .002)
TYP.
120 ° ± 5 ° STD.
FLAT ORIENTATION
(SHAFT AT CCW END)
1
CCW
2
POTENTIOMETER
3
Model 95 Solder Lug Terminals, "Triangular" Pattern
We turn lights on and off almost every day, but this simple switch is the basic unit that makes up the CPU.
Share this article and see how to build the CPU, a switch world that is either 0 or 1.
From ...
[i=s]This post was last edited by Hot Ximixiu on 2020-12-2 20:29[/i]This is an application of data transmission via the serial interface of msp430. The serial interface of SHTxx is not compatible with...
[Ask if you don't understand] Because I used a TI chip, the TPA32 series power amplifier chip, I saw the TINA-TI schematic analysis software on the official website. I wanted to see if I could generat...
This oxygen detector is produced by RKI of Japan, model number 0X-01. Judging from the date in the manual, it should be a product before 2004. It can be found on Taobao now, and the price is around 3K...
Ask an expert: Is this a no-routing layer added during PCB package design? There are many areas where electrical traces cannot pass through, as shown in the figure....
In February, Apple introduced a new "Tap to Pay on iPhone" feature that will allow compatible iPhones to accept payments through Apple Pay, contactless credit and debit cards, and other digital walle...[Details]
According to foreign media reports, German sensor manufacturer Toposens has collaborated with Infineon Technologies AG to achieve 3D obstacle detection and collision avoidance in autonomous driving s...[Details]
Question: Separate the two BCD codes stored in accumulator A, find their product, and put the product back into A in the form of compressed BCD code.
The circuit uses the minimum system, same as 1....[Details]
The "redundant design" of the PLC control system is mainly used in two aspects: one is the "redundant design" of the control circuit, such as the emergency disconnection circuit, etc.; the other is...[Details]
The LCD TV market has been growing rapidly in recent years. Market research firm DisplaySearch predicts a compound annual growth rate (CAGR) of 16% between 2008 and 2012, with total shipments expec...[Details]
The resistance of a conductor to electric current is called resistance, represented by the symbol R, and its units are ohm, kiloohm, and megohm, represented by Ω, KΩ, and MΩ respectively.
...[Details]
1. Introduction At present, MATLAB has been widely used in various fields of engineering design, such as electronics, communications, etc. It has become the most popular computer simulation softwar...[Details]
This paper mainly studies the parallel current sharing technology of Droop method DC/DC converters, and designs a current sharing converter with parallel output of two DC/DC converters based on f...[Details]
What are the differences and connections between ARM, DSP, FPGA, CPLD, SOPC, and SOC?
ARM is an embedded chip that is more powerful than a single-chip microcomputer and can add peripherals as neede...[Details]
Modern fighters are equipped with a variety of weapon systems such as air-to-air missiles, air-to-ground missiles, guided bombs, and aerial shells. At present, the main buses for exchanging data betw...[Details]
EFORT is a first-tier domestic robot company and has the initial ability to compete with international manufacturers.
EFORT is one of the few domestic robot companies that...[Details]
Preface
Virtual instruments and synthetic instruments have been a hot topic that industry insiders often talk about in recent years. Compared with traditional cabinet-type products, modula...[Details]
A combination of high technology and design: a screen-free smart bracelet uses innovative biometric technology to enable communication and contactless payment
Building blocks for the...[Details]
//Not much to say, let's go straight to the program void ADC1_DeInit(void) { ADC1- CSR = ADC1_CSR_RESET_VALUE; ADC1- CR1 = ADC1_CR1_RESET_VALUE; ADC1- CR2 = ADC1_CR2_RESET_VALUE; ...[Details]
0 Introduction
At present, there are many electronic locks based on IC card design on the market, which are widely used in hotels, apartments, warehouses, schools and other places. These o...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
