EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

155-2-006-0-S-BR0

Description
Board Connector, 6 Contact(s), 2 Row(s), Male, Right Angle, 0.079 inch Pitch, Solder Terminal, Locking
CategoryThe connector    The connector   
File Size1MB,1 Pages
ManufacturerMPE-Garry GmbH
Download Datasheet Parametric View All

155-2-006-0-S-BR0 Overview

Board Connector, 6 Contact(s), 2 Row(s), Male, Right Angle, 0.079 inch Pitch, Solder Terminal, Locking

155-2-006-0-S-BR0 Parametric

Parameter NameAttribute value
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.217 inch
subject depth0.337 inch
body length0.512 inch
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU
Contact point genderMALE
Contact materialCOPPER ALLOY
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Dielectric withstand voltage700VAC V
insulator materialTHERMOPLASTIC
Manufacturer's serial number155
Plug contact pitch0.079 inch
Match contact row spacing0.079 inch
Installation option 1LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.0066 mm
polarization keyPOLARIZED HOUSING
Rated current (signal)1.5 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.11 inch
Terminal pitch2.0066 mm
Termination typeSOLDER
Total number of contacts6
The zigbee terminal and the router cannot communicate with each other, but the coordinator can communicate with them
The coordinator and the terminal router communicate well, but the terminal and the router cannot communicate...
欧阳娜雪 RF/Wirelessly
DSP keyboard interface design source code
[size=4]Through this simulation experiment of matrix keyboard scanning LCD display under CCS2000 environment, I have learned and become familiar with the installation and debugging methods of CCS2000 ...
Aguilera DSP and ARM Processors
Switching Power Supply PCB Layout Technology
Switching Power Supply PCB Layout Technology...
造物工场 PCB Design
[NXP Rapid IoT Review] + Unfortunately, connection failed
Another week has passed. I tested it twice this week. The first time, as everyone said, I couldn’t connect to the Internet. After trying N times, I still failed. Later, I found that I needed to use a ...
CC_Cambrian RF/Wirelessly
How to disable ADC to reduce power consumption in ESP32
In micropython, there is currently no method to disable the ADC. Once the ADC is enabled, it cannot be turned off, so there is still more than 1 mA current in the sleep state, which is relatively high...
dcexpert MicroPython Open Source section
After using MAX735 to convert +5V to -5V, the dual-power op amp is powered and -5V is pulled down to 0V
As shown in the figure, I converted +5V to -5V through MAX735, and then supplied the positive and negative 5V to the dual power amplifier. Once powered on, -5V was pulled down to 0V. After disconnecti...
saa1653 Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号